We serviced a
AMANA WASHER
Model WTW5057LW0
Near Santa Fe, NM 87507
Joe
Job Details:
09/26/2024
Cx complaint. Washer won't start. Replaced lid lock and control ordered last visit. Tested unit. Unit good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Albuquerque, NM 87120
Larry
Job Details:
09/26/2024
Installed IM and tested good - Unit is good to go
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Santa Fe, NM 87507
Joe
Job Details:
09/26/2024
"Cx complaint, Dryer runs but drum not turning. Inspected unit, found belt broke and idler pulley stuck. Replaced Dryer repair kit. Tested unit. Unit good to go Advised cx about survey"
We serviced a
MAYTAG WASHER
Model MVW7230HC1
Near Los Ranchos de Albuquerque, NM 87107
Larry
Job Details:
09/26/2024
Installed parts listed and tested good - Unit is good to go
We serviced a
KITCHENAID RANGE
Model KSGG700ESS6
Near Granby, CO 80446
Antonio
Job Details:
09/26/2024
Installed new spark model and acu
We serviced a
MAYTAG DRYER
Model MED6630MBK0
Near Grand Lake, CO 80447
Antonio
Job Details:
09/26/2024
Installed acu and dryer kit unit tested good
We serviced a
WHIRLPOOL OVEN
Model WEE515S0LS2
Near Granby, CO 80446
Antonio
Job Details:
09/26/2024
Installed new acu and harness init tested good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT312CZJW00
Near Grand Lake, CO 80447
Antonio
Job Details:
09/26/2024
Installed new door seal and leveled up door unit tested good
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302ESS03
Near Carbondale, CO 81623
James R
Job Details:
09/26/2024
Signed disclaimer. Replaced R.H. F.F. door gasket. Formed to seal properly. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC302ESS03
Near Carbondale, CO 81623
James R
Job Details:
09/26/2024
Signed disclaimer. Replaced R.H. F.F. door gasket. Formed to seal properly. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MHW5630MBK0
Near Colorado Springs, CO 80911
Carlos
Job Details:
09/26/2024
Installed water valve and hoses in correct positions all ok
We serviced a
WHIRLPOOL WALL OVEN
Model WOED5030LZ01
Near Fountain, CO 80817
Carlos
Job Details:
09/26/2024
Installed door all ok
We serviced a
KITCHENAID ICE MACHINE
Model KUIX535HPA01
Near Carbondale, CO 81623
James R
Job Details:
09/26/2024
Started unit Hot water comes in. Unit is plumbed wrong hooked up to hot water. Plumber will need to redo supply to unit. Customer paid service call $149.95 auth code. 94U4PUPlease fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW4955HW3
Near Pueblo West, CO 81007
David
Job Details:
09/26/2024
"Replaced control, ran calibration cycle, and diagnostic cycle, all ran as expected."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ3
Near Colorado Springs, CO 80905
Glenn
Job Details:
09/26/2024
"Installed New Inlet Assy, Same Error, Installed New Sump & motor Assy. F9E1 - Draining: Product Not Draining , Found Suds inside (Left over soap inside tub & dispenser) Ran Diag Test 2 more times, All OPS Test:OK. Installed Leak Strip for safety."
We serviced a
WHIRLPOOL DRYER
Model WED5050LW1
Near Colorado Springs, CO 80918
Glenn
Job Details:
09/26/2024
"Re-seat connections to Control, Ran 15 min minimum Timed Dry Cycle, Signal Noise did run at end, however, it is very low & high pitched noise that customer can't even hear it sitting right next to dryer. Techline: No Volume controls to adjust sound. As Designed. SR# 7739998112"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Colorado Springs, CO 80921
Glenn
Job Details:
09/26/2024
"Install New Main PCB, Calibrate Unit, Diag Test: All OPS Test: OK"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Kiowa, CO 80117
Aaron
Job Details:
09/26/2024
"Capacitor is shorted out, harness broken between control and drain pump, removed and replaced components, tested unit, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL RANGE
Model WFG535S0LZ4
Near Kiowa, CO 80117
Aaron
Job Details:
09/26/2024
"Module is not sending power, harness is pinched in corner, removed and replaced components, tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Pueblo, CO 81005
David
Job Details:
09/26/2024
"Replaced control, ran calibration cycle, and then a diagnostic cycle, all ran as expected."
We serviced a
MAYTAG WASHER
Model MVW5430MW1
Near Grants Pass, OR 97526
Austin
Job Details:
09/26/2024
The units harness was replaced. The unit was tested multiple times while on property. The unit worked every time. Customer was advised to reach out if there was any other issues. The customer was provided a business card. The customer had the unit on its face and disconnected from the wall when I arrived on scene.
We serviced a
JENN-AIR WALL OVEN
Model JMW2430LL02
Near Sunriver, OR 97707
Levi
Job Details:
09/26/2024
Replaced user interface tested and oven tested good. Bake and broil elements turned on when the should. Temps checked okay
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Rifle, CO 81650
James R
Job Details:
09/25/2024
Signed disclaimer. Pump not working. Found a thong in drain pump. Removed reassembled and test operation it is operating as should. Customer paid service call $149.95 auth code. 9JCYEXPlease fill out tech satisfaction survey. Thank You
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Rifle, CO 81650
James R
Job Details:
09/25/2024
Signed disclaimer. Not agitating or spinning. Found a connector/wire broken at the shifter assy. Repaired. Also the control was faulty. Customer had one off another machine. Replaced. Test operation it is operating as should. Customer paid. $289.90 auth code 4VF4PV Please fill out tech satisfaction survey. Thank You.
We serviced a
GE WASHER
Model GFW550SSNW
Near Monument, CO 80132
Eric
Job Details:
09/25/2024
Replaced failed part and tested. Unit working properly at this time.
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Pueblo, CO 81005
James
Job Details:
09/25/2024
Installed ordered parts tested ops all ckok
We serviced a
SAMSUNG WASHER
Model WA44A3405AP/A4
Near Colorado Springs, CO 80923
Mathew
Job Details:
09/25/2024
Installed new dampers and belt. Test op. All okay.
We serviced a
SAMSUNG DRYER
Model DVE50R5400
Near Peyton, CO 80831
Mathew
Job Details:
09/25/2024
Replaced seized motor assy. Test op all okay.
We serviced a
MAYTAG DRYER
Model MED6230HW0
Near Colorado Springs, CO 80919
Glenn
Job Details:
09/25/2024
Install New Tstats & Element. All OPS Test:OK
We serviced a
MAYTAG DRYER
Model MED7230HW1
Near Peyton, CO 80831
Aaron
Job Details:
09/25/2024
"Heating element is shorted out, removed and replaced element, cleared unit of lint, tested unit, working and heating well now. Advised customer of survey."
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950UG/AA
Near Peyton, CO 80831
Brandon
Job Details:
09/25/2024
"Errors 7c pc 4c, bad neutral on the sub wire harness, repair neutral and tested op all checks ok, Svf paid $129.95 Auth# 9TURNU"
We serviced a
WOLF WALL OVEN
Model DO30PM/S/PH
Near Colorado Springs, CO 80908
Jerimiah
Job Details:
09/25/2024
"Picked up door, closing call."
We serviced a
BOSCH REFRIGERATOR
Model B36BT935NS/31
Near Edwards, CO 81632
Erik
Job Details:
09/25/2024
Unit performing as Intended. CX Believes the door was left ajar. No ice build up in its current state. Ice production normal. External enamel on FZ door Feels gritty and matte.Call BSH TAG: cosmetic NOT cover after 30 days please consult Mountain High Appliance for cosmetic concession CX may purchase SS panel BSH part#23001474 $810.66 P/L $189.95
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Vail, CO 81657
Antonio
Job Details:
09/25/2024
"Cx canceled, stating that the unit is under warranty"
We serviced a
DACOR RANGE
Model DOP48M96DHS
Near Colorado Springs, CO 80908
Brandon
Job Details:
09/25/2024
"Replaced burner thermostat burner working now, Called dacor for issue of blower fans coming on when back burners are turned on, same issue with steam function after replacing pump assy they said replace main PCB and water level sensor, Call nick when replacing pcb to give feedback, dacor ordered PCB and water level sensor"
We serviced a
THERMADOR VENT HOOD
Model VCIN36JP / 01
Near Colorado Springs, CO 80908
Eric
Job Details:
09/25/2024
Replaced failed light and tested. Light working properly.
We serviced a
KITCHENAID ICE MACHINE
Model KUIC15POZP2
Near Colorado Springs, CO 80908
Eric
Job Details:
09/25/2024
Replaced failed part and tested. Made first batch correctly. Customer will monitor.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC704FBS03
Near Monument, CO 80132
David
Job Details:
09/25/2024
"Replaced compressor, evacuated and charged with 4.5 oz of 134A. Good pressures and cooling."
We serviced a
GE RANGE
Model JB655YKCFS
Near Dillon, CO 80435
Erik
Job Details:
09/25/2024
Verify thermal failure Call GE TAG: case #14344605Job Complete
We serviced a
GE M/W OTR
Model JVM6175SK6SS
Near Gypsum, CO 81637
Erik
Job Details:
09/25/2024
No power to turn table motor/ hi side voltageCheck switch asm: upper door monitor misaligned If problem persist order WB10X35573JOB COMPLETE
We serviced a
THERMADOR COOKTOP
Model PCG366W/02
Near Edwards, CO 81632
Erik
Job Details:
09/25/2024
Install bull nose and logoJOB COMPLETECX not available for signature
We serviced a
JENN-AIR VENT HOOD
Model JXW8536HS2
Near Colorado Springs, CO 80921
Glenn
Job Details:
09/25/2024
"Vent door panel falling again. Replace clips and panel on last visit about 2 months ago. Techline: SR# 7739986727 ,Suggest replace same parts again, but transferred me to safety for autho. Safety Team indicates that they have chosen not to go forward with replacing the same parts, as it is not correcting the issue. They suggest closing this job ticket, and they will reach out to the customer. SR# 7739518096"
We serviced a
MONOGRAM REFRIGERATOR
Model ZISS480NNBSS
Near Edwards, CO 81632
Erik
Job Details:
09/25/2024
Install IM asmTest: connect to smartHQ service: PASSJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC0
Near Peyton, CO 80831
Aaron
Job Details:
09/25/2024
"Unit is not draining, inspected unit, found damaged control board, pump checks okay, but harness is broken, gearcase is leaking as well. Needs control, harness assembly to properly drain, and gearcase, stator, slider assembly to completely repair. Control w11510463 $308.20Harness w11568984 $110.48Gearcase w11449841 $357.20Slider assembly w10734521 $78.70Washplate w11510461 $119.26Rotor w11260238 $161.76Total parts $1,135.60Tax $93.12Supplies $14.50Hc $129.95Labor $249.95Total job $1,623.1230 day estimate No return on parts Auth 129.95 hc #KNR43J"
We serviced a
MAYTAG WASHER
Model MVW7232HW1
Near Rio Rancho, NM 87144
Joe
Job Details:
09/25/2024
"Cx complaint. Won't start cycle. Inspected unit, slider was broke. Replaced slider and tested. Unit good to go. Cx paid $463.33 by cc Payment authorization L939L3Advised cx about survey ; used 1 W10734521 (Slider) from stock"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRMG2272CF
Near Colorado Springs, CO 80924
Eric
Job Details:
09/25/2024
"Water dispenser leaking as it dispenses water. Upon inspection found that the fill tube had moved back causing water to come out into the dispenser housing. Adjusted fill tube and tested, water dispensing properly at this time."
We serviced a
WHIRLPOOL WASHER
Model GVW9959KQ2
Near Socorro, NM 87801
Larry
Job Details:
09/25/2024
CX complaint - Stopped draining - Inspected unit and found the drain pumped failed - Part are NLA for this modle
We serviced a
KITCHENAID REFRIGERATOR
Model KUBR204ESB00
Near Colorado Springs, CO 80908
Eric
Job Details:
09/25/2024
Replaced failed part. Compressor came on and unit is running.
We serviced a
AGA COOKTOP GAS
Model n/a
Near Elbert, CO 80106
Jerimiah
Job Details:
09/25/2024
"Pilot light will not stay lit, had two previous companies try repairing but no avail. Had pilot lighting/valve assembly replaced prior but pilot continually goes out after max an hour. Labor will be $269.95 upon return service. If chosen to do so, job will take at least 3-4 hours. $172.44 CC Auth# 93MV9PBypass screw KBYP211274 $70.98Thermocouple RG4M998603 $152.64"
We serviced a
SAMSUNG WASHER
Model WF53BB8900ADUS
Near Colorado Springs, CO 80922
Mathew
Job Details:
09/25/2024
"Replaced basket, tub assy, diaphragm. Test op all okay. RN three cycles and inspected for leaks. All Checks out ok."
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5300SRAA
Near Terrebonne, OR 97760
Levi
Job Details:
09/25/2024
"Replaced three listed parts. Used HASS to force cycles so I can watch temperature drops on the evaporators, inside the compartments. Hooked up my gauges to verify refrigerant pressures were still good. Had a good Frost pattern developing on the freezer evaporator and the unit started to cool. All fans and sensors are testing good. I hope this refrigerator works perfectly now."
We serviced a
SAMSUNG MICROWAVE
Model ME21R7051SG/AA
Near Colorado Springs, CO 80922
Jerimiah
Job Details:
09/25/2024
"Installed replacement door, unit check ok."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HFEDTSR/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
09/25/2024
Replaced ice maker kit and ice tray cycled ice maker all checks ok
We serviced a
U-LINE REFRIGERATOR
Model U-C02175FB-00
Near Colorado Springs, CO 80906
Eric
Job Details:
09/25/2024
Unit cooled after tech left then the filling say it began to warm up. Checked unit and found that it is the door magnet that is not working properly causing the unit to over work. Checked with Uline and office part is NLA.
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Peralta, NM 87042
Larry
Job Details:
09/25/2024
CX complaint - Cycle not starting - Inspected unit and found F7E4 error - Replaced slider with TSA and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM7
Near Rio Rancho, NM 87124
Joe
Job Details:
09/25/2024
Cx complaint. Dishwasher not heating inspected unit. Found heater damaged. Replaced heater and control. Tested unit. Unit good to go
We serviced a
WHIRLPOOL DRYER
Model WED4800BQ1
Near Eagle Point, OR 97524
Austin
Job Details:
09/25/2024
The units parts were replaced and the unit was tested. The unit performed well. The customer was advised to follow up with any issues and was provided a business card.
We serviced a
JENN-AIR DISHWASHER
Model JDB9800CWP2
Near Powell Butte, OR 97753
Levi
Job Details:
09/25/2024
Unit displayed f10-e3 error which is vent error. Checked resistance of fan motor and wax motor and they are in spec's. May be the board or vent system but I recommend getting both parts to eliminate chance at guessing wrong. Declined repair. $149.95 CK Auth# JW9X94
We serviced a
AMANA REFRIGERATOR
Model ARB2257CSR
Near Colorado Springs, CO 80919
Ralph
Job Details:
09/25/2024
"UNIT HAS A REFRIGERANT LEAK, CUST TO REPLACE UNIT...AUTHO NO. K4N39X"
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Belen, NM 87002
Larry
Job Details:
09/25/2024
CX complaint - Dryer making squeeling noise - Inspected unit and found the idler failing - Replaced with TS and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL WASHER
Model WTW4655JW2
Near Albuquerque, NM 87123
Jason
Job Details:
09/25/2024
Installed control unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Los Lunas, NM 87031
Larry
Job Details:
09/25/2024
Installed parts listed and tested good - Unit is good to go
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Albuquerque, NM 87109
Jason
Job Details:
09/25/2024
Checked unit found dryer is still having venting issues cx to get venting addressed spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Rio Rancho, NM 87124
Joe
Job Details:
09/25/2024
"Cx complaint. Not agitating. Inspected unit, found bad slider and damage to clutch. Replaced clutch and slider. Tested unit. Unit good to goAdvised customer about survey"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW2
Near Rio Rancho, NM 87124
Joe
Job Details:
09/25/2024
"Cx complaint. Dishwasher not draining or cleaning. Replaced drain pump, wash pump, control and ui. Tested unit. Unit good to goAdvised cx about survey"
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Albuquerque, NM 87111
Jason
Job Details:
09/25/2024
Installed control unit checks okSpoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ03
Near Albuquerque, NM 87108
Jason
Job Details:
09/25/2024
Installed parts unit checks okSpoke to cx about review
We serviced a
MAYTAG WASHER
Model MVWC565FW2
Near Elbert, CO 80106
Aaron
Job Details:
09/25/2024
"F7E6 error code upon arrival, actuator is shorted out, removed and replaced, recalibrated unit and ran through diagnostics, working well now. Advised customer of survey."
We serviced a
KITCHENAID RANGE
Model KSEG950ESS6
Near Vail, CO 81657
Antonio
Job Details:
09/25/2024
Installed new door honges unit tezted good
We serviced a
WHIRLPOOL WASHER
Model WETLV27HW3
Near Edwards, CO 81632
Antonio
Job Details:
09/25/2024
Installed ACU capacitor actuator unit tested good.
We serviced a
WHIRLPOOL WASHER
Model WFW8620HW4
Near Carbondale, CO 81623
James R
Job Details:
09/25/2024
Customer signed disclaimer. F8E1 long fill cleared code. Water supply is hooked up to one supply for 2 washers and the dryers. Called tech line. Each washer needs to be hooked up independent of each other. As well as the drain. Took pics and sent to whirlpool tech line. SR# 7739986748 Checked operation of each unit one at a time and units fill fine. Not covered under warranty. Customer paid service call $149.95 auth code. E9EY94Please fill out tech satisfaction survey. Thank You. Put a leak board under unit and took pic.
We serviced a
WHIRLPOOL DRYER
Model WED8127LW2
Near Colorado Springs, CO 80925
Carlos
Job Details:
09/25/2024
Recommend cx have vents cleaned installed heater and cutoff
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, CO 80917
Aaron
Job Details:
09/25/2024
"Removed and replaced control, recalibrated unit and ran through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW6230RHW3
Near Colorado Springs, CO 80918
Glenn
Job Details:
09/25/2024
"Customer played a video of unit making loud noise during spin cycle. Bad Gearcase, Splutch & Belt. Installed New GC, Splutch & Belt. All OPS Test:OK"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPW2
Near Pueblo, CO 81001
James
Job Details:
09/25/2024
Installed pre-ordered part tested ops all ckok left litmus
We serviced a
MAYTAG REFRIGERATOR
Model MSS25C4MGZ06
Near Pueblo West, CO 81007
James
Job Details:
09/25/2024
Found noisy fan due to blade not being situated correctly. Secured fan blade to proper position and leveled doors. Tested ops all ckok
We serviced a
KITCHENAID OVEN
Model KOEC530PSS00
Near Colorado Springs, CO 80908
Aaron
Job Details:
09/25/2024
"Removed and replaced copernicus and blower assembly, tested unit, working and heating well now, customer verified. Advised customer of 5 star survey."
We serviced a
KITCHENAID COOKTOP
Model KCGC506JSS00
Near Albuquerque, NM 87122
Jason
Job Details:
09/25/2024
Checked unit found regulator was stuck. took regulator off and inspected. put regulator back on unit checks okSpoke to cx about review
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Colorado Springs, CO 80922
Aaron
Job Details:
09/25/2024
"Removed and replaced ice maker and fan, tested unit through harvest and fill cycles, working well now, needs time to cool. Advised customer of 5 star survey."
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ3
Near Colorado Springs, CO 80905
Carlos
Job Details:
09/25/2024
Installed UI ran test all ok
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Peyton, CO 80831
Aaron
Job Details:
09/25/2024
"Drain pump is shorted out, removed and replaced pump assembly, tested unit, working well now, installed litmus strip and advised customer of survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF555SDFZ18
Near Colorado Springs, CO 80923
Aaron
Job Details:
09/25/2024
"Solenoid is not engaging auger properly, removed and replaced components, tested unit, working well now, customer verified. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Central Point, OR 97502
Austin
Job Details:
09/25/2024
"SR7739929028. Unit is getting replaced per the safety team due to the injury. SR7739986887 Tech line - it was verified with Techline that both the high limit thermostat and the heater were shorted to ground, allowing the unit to runaway heat. This burned the heating element which causes smoking.. tech lines recommendation was to replace the parts. However, the Safety Team made the call to replace the unit. Both SR numbers are attached to this. The customer was advised theyd be contacted about replacing the unit. The plug was removed from the unit, and the customer was advised not to use the unit until the new one shows up ."
We serviced a
WHIRLPOOL RANGE
Model WEG745H0LZ5
Near Bend, OR 97702
Levi
Job Details:
09/25/2024
"Replace left front burner and electrode, tested and all checks okay."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Medford, OR 97504
Austin
Job Details:
09/25/2024
The units parts were replaced. The unit was tested has no error codes and is working. The customer is going to run a couple loads of laundry and follow up if they have any issues.
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Avon, CO 81620
Erik
Job Details:
09/25/2024
Unit NOT level - LEVEL UNITConnect to smartHQ service: multiple error codes/ alert * see quick picsCritical lid lock failure: Replace lid lock asm WH44X10288Call tech line/ Wright technologies will review and dispatch for return service
We serviced a
JENNAIR WALL OVEN
Model n/a
Near Colorado Springs, CO 80915
Jerimiah
Job Details:
09/25/2024
Bake element coming on immediately without control. Stuck relay? Relay board needs replacing. Part is discontinued. Cust will look for part. Labor will be $249.95 if Cust is able to find board. Charging service call $149.95 CC Auth# KX44N4(WP)74006612 relay board
We serviced a
MAYTAG REFRIGERATOR
Model MSS25C4MGZ08
Near Rio Rancho, NM 87144
Larry
Job Details:
09/24/2024
Arrived and foud the FC temps between -3 and 5 degrees and the RC between 36 and 34 degrees - The unit is pulling .04 amps and 97.5 watts - Unit is operating as designed - Called techline to document (SR7739977491)
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ2
Near Santa Fe, NM 87507
Jason
Job Details:
09/24/2024
Installed part unit opperation checks okSpoke to cx about review
We serviced a
MAYTAG DRYER
Model MED6230HC2
Near Santa Fe, NM 87507
Jason
Job Details:
09/24/2024
Installed control unit checks okspoke to cx about review
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JS0
Near Albuquerque, NM 87120
Larry
Job Details:
09/24/2024
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHV00
Near Santa Fe, NM 87507
Jason
Job Details:
09/24/2024
Installed lights unit checks okSpoke to cx about review
We serviced a
MAYTAG WASHER
Model MVWC565FW1
Near Colorado Springs, CO 80920
Glenn
Job Details:
09/24/2024
"Install New Gearcase, Cam Kit & Belt, All OPS Test:OK"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300EBS08
Near Silverthorne, CO 80498
Antonio
Job Details:
09/24/2024
Found frezzer panel lose tightened screws unit tested good
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Silverthorne, CO 80498
Antonio
Job Details:
09/24/2024
Installed acu and pump unit tested good
We serviced a
KITCHENAID DISHWASHER
Model KDFE204KPS1
Near Basalt, CO 81621
James R
Job Details:
09/24/2024
Customer signed disclaimer. Replaced dispenser. Test operation. Operating as should. Please fill out tech satisfaction survey. Thank You.Put a leak board under unit.
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS00
Near Colorado Springs, CO 80924
Aaron
Job Details:
09/24/2024
"Top metal cover showing above UI console, pulled unit and corrected, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Fountain, CO 80817
Carlos
Job Details:
09/24/2024
Loose bolt in gearcase retighten all ok
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS00
Near Colorado Springs, CO 80917
Glenn
Job Details:
09/24/2024
Found freezer door gasket not sealing at Top RS corner. Defrosted Ice buildup in freezer. Dry cabinet and rails. Adjust door gasket. All OPS Test:OK
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS2
Near Colorado Springs, CO 80919
Glenn
Job Details:
09/24/2024
"Install New Vent, Gasket & Deflector, Main PCB & UI Console, Diag Test:OK, Customer will continue to monitor."