We serviced a
WHIRLPOOL RANGE
Model WFES3330RZ2
Near Breckenridge, Colorado 80424
Antonio
Job Details:
03/24/2026
Installed new acu then heated oven to 350?for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
MAYTAG WASHER
Model MTW6200RF1
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
03/24/2026
Called techline 22986957 unit works as design. Noise is normal operation of unit engaging slider and clutch
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
03/24/2026
"Installed drain pump, ran tests all ok"
We serviced a
MAYTAG WASHER
Model MVW4505MW2
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
03/24/2026
"Releveled unit leveling feet, ran calibration. Ran test runs all ok. Cx needs to ensure all loads are properly balanced."
We serviced a
SAMSUNG REFRIGERATOR
Model RF90F29EECRAA
Near Colorado Springs, Colorado 80920
Mathew
Job Details:
03/24/2026
"No display. Confirm power to display, replace display. Test op all okay."
We serviced a
MAYTAG DRYER
Model MED6230HW4
Near Fountain, Colorado 80817
Carlos
Job Details:
03/24/2026
Installed leveling feet all ok
We serviced a
MAYTAG WASHER
Model MFW7020RF0
Near Breckenridge, Colorado 80424
Antonio
Job Details:
03/24/2026
Installed new water valves and pressure switch then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HS12
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
03/24/2026
"Installed capacitor, transformers, magnetron and diode. Ran tests runs all ok."
We serviced a
MAYTAG WASHER
Model MVWB835DW2
Near Colorado Springs, Colorado 80919
Jason
Job Details:
03/24/2026
Destroyed old agitator wash plate. Replace the agitator wash plate with the new plate and new bolt. Informed customer that I use penetrating oil and do a tub clean before washing her clothes. Tested unit no issues found unit repaired.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS04
Near Colorado Springs, Colorado 80918
Jason
Job Details:
03/24/2026
Replace main control user interface and air dampener for the refrigerator. After plugging in and testing the unit the air damper was able to cycle. No other issues found unit repaired.
We serviced a
KITCHENAID WALL OVEN
Model KOES530PSS00
Near Basalt, Colorado 81621
James R
Job Details:
03/24/2026
F2E1 shorted key pad. Replaced console test operation. Is operating as designed. Customer oked to go in and do repair. Not available to sign ticket. Please fill out tech satgisfaction survey. Thank You.
We serviced a
JENN-AIR WALL OVEN
Model JMW2430IL03
Near Bend, Oregon 97702
Levi
Job Details:
03/24/2026
Replaced oven console tested and all checks okay
We serviced a
MAYTAG WASHER
Model MHW8630HC4
Near Carbondale, Colorado 81623
James R
Job Details:
03/24/2026
F5E3 door lock cleared code was only code present and then test cycled thru test 12 went thru no issues.No error codes returned. Customer indicated that the soap dispenser wasnt working. It was empty. Filled and then checked for soap dispensing is ok. Could see soap in tub. Ran thru a rinse and spin to flush out soap. If customer doesnt want to use the soap dispenser will need to put soap in thru the front of unit when starting.The only thing I can contirbute to the lack of spinning right at times is a over load or a out balance load. Either of these can cause unit not to spin out properly. Unit will try to balance load but if it cant it will stop the cycle. Unit goes into high speed spin and sounds normal. Cuistomer paid service call $249.95 auth code. L9U3W9 Please fill out surv
We serviced a
WHIRLPOOL RANGE
Model WFG505M0BS3
Near Albuquerque, New Mexico 87104
Larry
Job Details:
03/24/2026
Installed ignitor and tested good - Unit is good to go
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ1
Near Glenwood Springs, Colorado 81601
James R
Job Details:
03/24/2026
Signed disclaimer. Removed unit and then removed outer door panel and replaced both door hinges were broke. Re-assembled is working as should. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ2
Near Glenwood Springs, Colorado 81601
James R
Job Details:
03/24/2026
Sign disclaimer. Removed drain pump. Found glass in pump and blades as well as the motor pump assy beat up. Would need both was able to blow thru drain line. Filled unit and then tried to drain and it still wont. Gave customer estimate to repair. $744.93 they paid the service call only. $149.95 auth code 94TJ4H
We serviced a
MAYTAG WASHER
Model MVW5035MW2
Near Eagle Point, Oregon 97524
Kyle
Job Details:
03/24/2026
"Found unit will lock and unlock, then motor would try to turn, and unit would shoot to done within 30 seconds. Replaced capacitor and retested. Unit is operating as intended."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM13
Near Albuquerque, New Mexico 87120
Larry
Job Details:
03/24/2026
CX complaint - IM not working - Inspected unit and found the IM failed - Replaced IM and tested good - Unit is good to go - Survey mentioned
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AFL
Near Dillon, Colorado 80435
Antonio
Job Details:
03/24/2026
Installed new acu then cycled unit on for proper operation and unit tested good
We serviced a
SAMSUNG MICROWAVE
Model ME17R7021ES/AA
Near Colorado Springs, Colorado 80925
Brandon
Job Details:
03/24/2026
"Replaced door and latch, tested operation all checks ok"
We serviced a
SAMSUNG RANGE
Model NE63A6511SSA
Near Colorado Springs, Colorado 80911
Brandon
Job Details:
03/24/2026
Replaced regulators and tested operation all checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDZ05
Near Albuquerque, New Mexico 87120
Larry
Job Details:
03/24/2026
Installed IM kit and tested good - Unit is good to go - Survey mentioned
We serviced a
BOSCH RANGE
Model HDS7052U/08
Near Glenwood Springs, Colorado 81601
Sean
Job Details:
03/24/2026
Verified the unit information & customer signed disclaimer.Set unit to 250? temp was 15? lower than set point.Adjusted the temp calibration 15? hotter .Tested the unit heated up to 260? Adjusted the temp -5 ? unit heated to set point accurately.Set to 270? heats to 270?>The customers thermometer in the oven is no good ..SVC $189.95Labor $ 149.95Customer paid 339.90Auth code kyf33e
We serviced a
BOSCH DISHWASHER
Model SHE41CM5N/29
Near Elbert, Colorado 80106
Ryan
Job Details:
03/24/2026
Made adjustment to dispenser door and it is now working properly. Tested unit and all is working properly. RK
We serviced a
JENN-AIR WALL OVEN
Model JJW2730WS02
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
03/24/2026
"Customer states unit is tripping the breaker and the breaker is hot, inspected unit, unit has proper power and polarity, ensured connections are tight at the terminal block, no errors in diagnostics, elements check as follows:Upper broil 16.0 and 14.7 amps during use, Convection element 17.2 and 15.0 amps,Upper bake20.3 and 11.9 amps,Lower broil 16.2 and 14.9 amps,Lower bake 20.5 and 11.9 amps, tested both cavities to 350f, heating well at time of inspection. Auth $169.95 hc #F4H4HU"
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Silverthorne, Colorado 80498
Antonio
Job Details:
03/24/2026
Called tech Case#22980298 whlp recommending clean back to back white vinger and all fresh tablets no error codes stored unit is working properly
We serviced a
GE RANGE
Model JB256RT3SS
Near Rifle, Colorado 81650
Clint
Job Details:
03/24/2026
Customer signed discalimer and recieved parts ordered. Pulled unit out and replaced wiring and control. Set personality on control and units bake and broiler now work correctly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
MAYTAG WASHER
Model MHW5630HC2
Near Colorado Springs, Colorado 80927
Earl
Job Details:
03/24/2026
Customers complaint customer states that out of 10 loads 1 will not spin out i tested the unit and couldn't find anything issue i contacted may tag and got no case number 22977316
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT348FMES05
Near Leadville, Colorado 80461
Antonio
Job Details:
03/24/2026
Unit needs compressor Sc$149.95 CC Auth# EHM9CU
We serviced a
KITCHENAID DISHWASHER
Model KDTM405PPS1
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/24/2026
"Door panel dented on left side, left side of UI control broken as well, removed and replaced components, no scratches or dents, verified by customer, tested unit through diagnostics, working well. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80920
Jason
Job Details:
03/24/2026
"Found that the unit was stuck in a flood mode. Unable to get into diagnostics. Replace the main control board calibrated and tested unit no issues found, spoke about survey to customer. Unit repaired"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF341PAPM2
Near Colorado Springs, Colorado 80922
Jason
Job Details:
03/24/2026
Tested incoming power and found that the live was swapped with the ground. Swap wires around and found that the control was still not responding. Replace the control and test at the unit and calibrated. No issues found unit repaired.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80917
Aaron
Job Details:
03/24/2026
"Control is sending constant power to the drain pump, removed and replaced control, recalibrated and tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
SAMSUNG DRYER
Model DVE55CG7500EA3
Near Pueblo, Colorado 81001
Domingo
Job Details:
03/24/2026
Replaced blower and heat element test it h it with vent on didnt pass c80 took vent out test it it passed without vent needs to be clean the vent of dryer the ones that goes to the out side
We serviced a
FRIGIDAIRE RANGE
Model GCFI3060BFE
Near Colorado Springs, Colorado 80923
Earl
Job Details:
03/24/2026
"Customers complaint when the customer wipes the cooktop off. Prior to cooking, the unit will beep and sometimes it will not function or come on for about 2 minutes. After 2 minutes, you can turn the power on his complaint ISIS the original 9 months. The unit did not have this issue? I replace the generator boards and the user interfaces on the unit. I inform the customer. My guess is that they change something in the algorithm function of the unit. So it's trying to make sure there is no false starts. So when you wipe the unit down, you have to wait 2 minutes before you can turn it on. That is still just a guess. I also had Ati d tech on the phone with me talk, discussing this issue All this is documented unit is operating properly at this time"
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HB10
Near Medford, Oregon 97501
Kyle
Job Details:
03/24/2026
Replaced upper and lower door switch assemblys. Tested unit. Unit is operating as intended.
We serviced a
BOSCH MICROWAVE
Model HMC80252UC/05
Near Monument, Colorado 80132
Ryan
Job Details:
03/24/2026
"Installed filter board and tested operation, Unit now working properly. RK"
We serviced a
GE WASHER
Model GFW550SSN1WW
Near Silverthorne, Colorado 80498
Erik
Job Details:
03/24/2026
DRAIN OVER FLOWING - NEED PLUMBER CX AWARE
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model GFE29HSDASS
Near Colorado Springs, Colorado 80905
Charles
Job Details:
03/24/2026
"Aglign filter head and install filter, Service fee $149.95, Labor $90.00, Total $239.95 paid autho AJ4N9A"
We serviced a
SAMSUNG MICROWAVE
Model ME16A4021AS/AA
Near Colorado Springs, Colorado 80938
Mathew
Job Details:
03/24/2026
Replace door assy. Test op all okay.
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW
Near Portland, Oregon 97266
Austin
Job Details:
03/24/2026
3/24/26 AB: removed and replaced main control board. Ran a calibration and tested a quick wash cycle. Now the unit fills to proper level and begins a wash cycle. No draining issues and unit is operational. Service complete
We serviced a
SUB ZERO REFRIGERATOR
Model BI - 36U/S/PH
Near Portland, Oregon 97229
Austin
Job Details:
03/24/2026
3/25/26 AB: before arriving onsite customer informed tech that a different company came out before us and installed the part. Unit is working and service is complete
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Fountain, Colorado 80817
Charles
Job Details:
03/24/2026
Replaced lid and bezel
We serviced a
JENNAIR DISHWASHER
Model JDB8000AWS3
Near Redmond, Oregon 97756
Richard
Job Details:
03/24/2026
Tested unit not draining checked drain pump all checked fine retested all tested ok unit working as designed.customer paid Service fee by check#2365 auth#4P3MV9
We serviced a
KITCHENAID WALL OVEN
Model KOES530PSS00
Near Rifle, Colorado 81650
James R
Job Details:
03/24/2026
Printed labels took pics ready to send.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo West, Colorado 81007
James
Job Details:
03/23/2026
Installed pre-ordered control per sf. Recalibrated unit and tested all ops ckok
We serviced a
BOSCH DISHWASHER
Model SHS43CF5/27
Near Pueblo West, Colorado 81007
James
Job Details:
03/23/2026
Found upper spray arm dislodge from supply tube. Secured and tested. All ops test good. Unit is in warranty
We serviced a
LG REFRIGERATOR
Model LFCS22520D
Near Portland, Oregon 97266
Jesse
Job Details:
03/23/2026
Replaced and tested parts. Verified functional w no errors.
We serviced a
KITCHENAID RANGE
Model KSGS330SPS0
Near Edgewood, New Mexico 87015
Jason
Job Details:
03/23/2026
Checked unit took burner apart and put it back together. burner is now lighting unit operation checks ok. spoke to cx about review
We serviced a
MAYTAG WASHER
Model MVW7232HW2
Near Pueblo, Colorado 81005
James
Job Details:
03/23/2026
"Found rotor loose causing noise secured, leveled unit and tested. All ops test good"
We serviced a
MAYTAG WASHER
Model MVW6200KW3
Near Grand Junction, Colorado 81504
James R
Job Details:
03/23/2026
Signed disclaimer. F0E9 error off balance. Cleared code.Pause cycle re-distribute load to balance. When loading distribute items evenly. Checked suspension is good. Replaced drain pump. Test in service test checked ok. Started a bulky items test high wtr fill. Unit is operating as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Pueblo West, Colorado 81007
Domingo
Job Details:
03/23/2026
Roleaced gear case and nut spanner and test it machine test it good
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Grand Junction, Colorado 81504
Sean
Job Details:
03/23/2026
Verified the unit information & customer signed disclaimer.Pulled the unit out and unplugged it from the wall .Removed the back panel and removed the heater .Installed the new heater and cut-off. Reassembled the unit and tested. The unit started Heated and spinning. Tested good.Thank you.Please go on line to D-3 A-OK Appliance service inc.And fill out a technician survey.Thank you Your technician.Sean..
We serviced a
FISHERPAYKEL RANGE
Model RDV-484GG-N
Near Colorado Springs, Colorado 80918
Ryan
Job Details:
03/23/2026
"Installed relay with not improvement. Unit needs wiring replaced, wire harness is not a servicable part per techoine. RK"
We serviced a
LG MICROWAVE
Model LMC2075ST
Near Colorado Springs, Colorado 80919
Brandon
Job Details:
03/23/2026
Replaced touch pad and tested operation all checks ok
We serviced a
LG FREEZER
Model LFDS22520S
Near Gypsum, Colorado 81637
Antonio
Job Details:
03/23/2026
Installed new compressior and drier then charged unit with r600 and freezer is at 0?and fridge at 35? unit is working properly
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Peyton, Colorado 80831
Aaron
Job Details:
03/23/2026
"Door bellow has worn from use, removed and replaced, tested unit, working well now. Advised customer of situation and survey."
We serviced a
GE COOKTOP
Model JP3036TL3WW
Near Eagle, Colorado 81631
Erik
Job Details:
03/23/2026
install/ test: passjob complete
We serviced a
MAYTAG DRYER
Model MDE5500AYW
Near Colorado Springs, Colorado 80918
Ryan
Job Details:
03/23/2026
"Tightened several loose screws, unit is now working properly. RK149.95Auth X9T9X3"
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Larkspur, Colorado 80118
Jason
Job Details:
03/23/2026
Replace main control in calibrated intested unit no known issues found unit repaired.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRUF2020AW3
Near Prospect, Oregon 97536
Chris
Job Details:
03/23/2026
"Replaced the compressor, filter Dryer,starter,and capacitor. Unit held vacuum. Customer is going to monitor it."
We serviced a
WHIRLPOOL DRYER
Model WED4720RW0
Near Grants Pass, Oregon 97527
Chris
Job Details:
03/23/2026
Replaced moisture sensor wire harness. The customer is going to monitor it.
We serviced a
LG WASHER
Model WM3600HVA
Near Pueblo, Colorado 81005
James
Job Details:
03/23/2026
"Found loose dispenser to tub hose causing leak, secured and tested all ops test good. Advised have licensed plumber out to address slight backup of drain standpipe"
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS0
Near Sandia Park, New Mexico 87047
Jason
Job Details:
03/23/2026
Installed element ran quick cycle unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87112
Jason
Job Details:
03/23/2026
Installed valve ran quick cycle unit operation checks ok. spoke to cx about review
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS01
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/23/2026
"Turntable ring and coupler are squeaking during use, removed and replaced, tested unit, working and heating well now, verified by customer. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/23/2026
Arrived and removed failed control. Installed new control. Recalibrate unit. Tested washer on quick cycle. Unit is functioning now as designed. No further issues noted.
We serviced a
KENMORE WASHER
Model 11026902690
Near Colorado Springs, Colorado 80907
Earl
Job Details:
03/23/2026
Install the new drain pump.We couldn't test it because it's on a concrete floor some of the water came out onto the floor b impossible to figure out whether or not it was leaking at this point
We serviced a
GE REFRIGERATOR/TOP
Model GSE25GYPHCFS
Near Colorado Springs, Colorado 80911
Earl
Job Details:
03/23/2026
I installed the freezer door on the side by side.That was waiting for me unit is operating properly at this time
We serviced a
KITCHENAID WALL OVEN
Model KOEC530PSS01
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
03/23/2026
"Removed and replaced components, tightened common wire at the junction box, tested unit, working and heating well now, verified by customer. Advised customer of 5 star survey. Case number 22964888"
We serviced a
THERMADOR DISHWASHER
Model DWHD770CFM/22
Near Avon, Colorado 81620
Erik
Job Details:
03/23/2026
FD 0305 00084INSTALL/ TEST: PASSJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Albuquerque, New Mexico 87109
Jason
Job Details:
03/23/2026
Installed control. ran calibration cycle and quick wash cycle unit operation checks ok. spoke to cx about review
We serviced a
MONOGRAM REFRIGERATOR
Model ZISB420DHB
Near Colorado Springs, Colorado 80921
Charles
Job Details:
03/23/2026
Replaced upper led light switch
We serviced a
KITCHENAID DISHWASHER
Model KDPM604KPS1
Near Albuquerque, New Mexico 87106
Jason
Job Details:
03/23/2026
Checked unit found wash motor not starting. pump motor assy needs replaced SC$149.95MPS$17.50LABOR$239.95PUMP MOTOR ASSY#W11416362$352.67TX$64.61TOTAL$824.68Auth code: F9JC4T$162.70
We serviced a
GE REFRIGERATOR
Model GFE28GSKMSS
Near Colorado Springs, Colorado 80911
Earl
Job Details:
03/23/2026
"Customers, complaint units is not making ice. I got ahold of g. E, and they ran me through diagnostics. Their suggestion is a frozen water line. The customer had already let it sit for 72 hours without running it, and it is in the refrigerator door and it still did not fill up with water, we're getting water to the solenoid cluster, but not past it. I quoted the price for new door the customer declined and paid the service fee authorization codeAJLXT3"
We serviced a
WHIRLPOOL RANGE
Model WFES3330RZ0
Near Grants Pass, Oregon 97527
Chris
Job Details:
03/23/2026
Replaced both hinges and tested. The condition has improved but I think it's normal.
We serviced a
MAYTAG WASHER
Model MVWP586GW0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/23/2026
"Control is intermittently working, removed and replaced, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW500CMW0
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
03/23/2026
"Arrived and cx complaint of not finishing cycle. Cx had loaded towels. Started cycle then switched it you normal. She said it ran through but then wouldn't stop at end of cycle. She hadn't used it again. I arrived and ran rinse spin, and a quick wash. Both finished and seemed to run fine. Can't duplicate issue She had. Asked her to run a few more loads and let us know."
We serviced a
KITCHENAID WALL OVEN
Model KOED530PPS01
Near Colorado Springs, Colorado 80921
Jason
Job Details:
03/23/2026
"Installed new receiver and screws, test of the door and made sure that there were no issues how the customer test as well, unit repaired."
We serviced a
KITCHENAID DISHWASHER
Model KDTE334GPS0
Near Colorado Springs, Colorado 80920
Charles
Job Details:
03/23/2026
Will not power up until unplugged and then plugged back in. Replaced main control board
We serviced a
LG DRYER
Model DLE3600V
Near Pueblo, Colorado 81005
James
Job Details:
03/23/2026
Found loose wire at cntl causing intermittent heating secured and tested. All ops test good. Advised cust to have licensed dryer vent cleaner out to address slight vent restriction
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near La Pine, Oregon 97739
Levi
Job Details:
03/23/2026
Replace control board and also a flipped around the inlet hoses so that way the water temperature would match the proper valve. Test it and all checks okay perform to recalibration cycle.
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near La Pine, Oregon 97739
Levi
Job Details:
03/23/2026
Replace door boot seal and door locker assembly. Tested and no leaks at time of service and unit it seems to be working just fine. During testing I didn't notice I had an error code for something and I witnessed some suds in the machine so advice customer to use less soap. Drain pump seems to be operating just fine
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo, Colorado 81004
Domingo
Job Details:
03/23/2026
Replaced control board ran calibration; test it machine and machine is good
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS322FDAM04
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/23/2026
"Removed and replaced modules, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
MAYTAG WASHER
Model MVW6200KW5
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
03/23/2026
Arrived and removed failed parts. Installed new parts. Tested washer on quick cycle. Unit is functioning now as designed.
We serviced a
GE W/D STACKED UNIT
Model GUD27ESSMWW
Near Grand Junction, Colorado 81501
Sean
Job Details:
03/23/2026
Verified the unit information customer signed disclaimer.Checked the unit for error codes.Found OBB and water supply .Checked the water and found the hot water was off. I turned it on and checked for leaks.Removed the front panel and ran a spin test found that the inner-drum was loose from the outer drum and was wobbly.Removed the auger and tightened the drum nut.Reassembled the unit and leveled it.Tested the unit it completed all the tests and no longer shaking.Tested the unit good.Please go online to D-3 A-OK Appliance service inc.And complete a technician survey.Your technician.Sean...
We serviced a
LG WASHER
Model WM1814CW
Near Colorado Springs, Colorado 80906
Mathew
Job Details:
03/23/2026
"Drain pump now making grinding noise, no debris found inside pump. Pump not shutting off. Recommend drain pump and water level sensor replacement at same time. Pump needs replaced. Part $110.34Tax $9.05MPs $14.50Labor $209.95$343.846601ER1006A $118.34Tax $9.70Complete repair total $471.88"
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Albuquerque, New Mexico 87105
Larry
Job Details:
03/23/2026
CX complaint - Not filling - Inspected unit and found dibris in the valve - Cleared dibris and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF560SEHB05
Near Seaside, Oregon 97138
Nathan
Job Details:
03/23/2026
Unit is working CX instruct about loading and temp settings were all the way cold
We serviced a
WHIRLPOOL WASHER
Model WFW5605MC1
Near Albuquerque, New Mexico 87105
Larry
Job Details:
03/23/2026
Arrived and the home in unsanitary conditions with the smell being unbearable and urine and feces all over the floor making it very sticky and unworkable
We serviced a
GE WASHER-DRYER COM
Model GUD24ESSM1WW
Near Beaver Creek, Colorado 81620
Erik
Job Details:
03/23/2026
DRUM RUBBING ON RIGHT SIDE WALL SUPPORTMOUNT SCREW MISSING FROM MANUFACTURERREPLACE WITH PERSONAL HARDWARE AND TEST: PASSJOB COMPLETE
We serviced a
MIELE DISHWASHER
Model G7366
Near Vail, Colorado 81657
Erik
Job Details:
03/23/2026
CONNECT TO MDU - NO ERRORS LOGGEDAPPLY VARIANT PROGRAM (2ND ATTEMPT) - CALL MIELE TAG: CHECK PRESSURE SENSOR: GOODTEST INTAKE: GOODTEST DRAIN: GOODJOB COMPLETETEST ON NORMAL: PASSREF# 1011308236
We serviced a
MAYTAG REFRIGERATOR
Model MRT311FFFH01
Near Albuquerque, New Mexico 87105
Larry
Job Details:
03/23/2026
CX complaint - Still not cooling and getting condensation - Inspected unit and found a large gap between the liner and cabunet - Called techline (SR22970095) to document - Unit is unrepairable
We serviced a
WHIRLPOOL DRYER
Model WED5100HC4
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/23/2026
"Metal bracket vibrating against blower housing, corrected and tested unit, working and heating well now. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
03/23/2026
"Drive cam gears rattling, replaced and leveled unit, lower harness clip taghing against back panel, put drain hose in best place to help prevent tapping, tested unit through diagnostics, working well now. Advised customer of situation and survey."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model PRSC2222AFA
Near Seaside, Oregon 97138
Nathan
Job Details:
03/23/2026
Seized and failed evap fan motor in freezer replaced Tested Advised of survey
We serviced a
MAYTAG WASHER
Model MVW7230HW2
Near Colorado Springs, Colorado 80917
Jason
Job Details:
03/23/2026
"Stator bolt were loose, causing the cover piece to move during agitation when it was going back and forth. Tighten it down and test it again, level unit for customer no more issues found, unit repaired"
We serviced a
SUBZERO REFRIGERATOR
Model CL485OSIDSP
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
03/23/2026
"FOUND ICE ON THE BACK WALL. ALSO ON THE DOOR FRAME AT THE TOP, SOMETHING WAS HOLDING DOOR OPEN AND ALLOWING CONDENSATION BUILD UP THAT WAS CASUING UNIT TO ICE UP, CLEARED ALL THE ICE AND UNIT CHECKED OKAY, CUST TO MONITOR"
We serviced a
MAYTAG WASHER
Model MTW7200RF0
Near Peyton, Colorado 80831
Aaron
Job Details:
03/23/2026
"F0E5 off balance error code in diagnostics, leveled unit and seated tub onto gearcase splines, put unit in best possible spot to help prevent tapping of drain hose. Advised customer of situation and survey."