We serviced a
LG WASHER
Model WM3400CW
Near Colorado Springs, Colorado 80908
Charles
Job Details:
09/18/2026
Replaced leaking dispenser
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ4
Near Redmond, Oregon 97756
Richard
Job Details:
09/18/2026
"Installed new inlet valve assembly cycle tested unit all tested fine at this time, found small drip from waterline to unit, showed customer needs to have new waterline to dishwasher installed by a plumber."
We serviced a
SUBZERO REFRIGERATOR
Model BI-48S/S/TH
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
09/18/2026
"INSTALLED LISTED PARTS ANDF UNIT STARTED WORKING, CUST TO MONITOR"
We serviced a
FRIGIDAIRE MICROWAVE
Model FGMO3067UF
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
09/18/2026
INSTALLED PART AND UNIT CHECKED OKAY
We serviced a
WOLF RANGE
Model DF60650CG/S/P
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
09/18/2026
"BURNERS ARE IGNITING CORRECTLY, UNIT CHECKED OKAYU"
We serviced a
SUB ZERO WALL OVEN
Model SO3050TE/S/T
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
09/18/2026
SET UNIT UP ON WIFI AND TIME STARTED WORKING CORRECTLY
We serviced a
WHIRLPOOL DRYER
Model WED8127LC3
Near Frisco, Colorado 80443
Antonio
Job Details:
09/18/2026
"Installed new cntrl, tstat and also fixed ducting leading to wall. Unit is heating and working properly"
We serviced a
ELECTROLUX WASHER
Model ELFW7637AT2
Near Dillon, Colorado 80435
Antonio
Job Details:
09/18/2026
"Found washer, unlevel level washer out washer's not wood. Shaking nor moving anymore unit's working properly."
We serviced a
GE CAFE MICROWAVE OVEN
Model CVM517P2R1S1
Near Breckenridge, Colorado 80424
Erik
Job Details:
09/18/2026
CX CLAIMS SMOKE DOES NOT EXHAUST - UNIT SET FOR RECIRCULATE NO FIX* SEE QUICK PICSCX CAN HAVE HVAC CUT VENT TO EXTERIOR TO PROPERLY VENT JOB COMPLETE
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRMC2273CF00
Near Medford, Oregon 97501
Kyle
Job Details:
09/18/2026
"Removed ice maker assembly, removed ice maker housing, removed auguer motor and installed new auger motor and bar drive, re installed ice maker housing and ice maker assembly, tested unit, unit is operating as intended."
We serviced a
THERMADOR OVEN
Model MEDMCW71JS/05
Near Warrenton, Oregon 97146
Nathan
Job Details:
09/18/2026
Replaced cooling fan due to failure Tested Advised of survey
We serviced a
MAYTAG WASHER
Model MVW6200KW5
Near Warrenton, Oregon 97146
Nathan
Job Details:
09/18/2026
Disclaimers sentDoor strike missing out of boxInstalled newTestedAdvised of survey
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
09/18/2026
Installed control board ran tests and calibration runs all ok
We serviced a
MAYTAG DRYER
Model MED6200KW1
Near Albuquerque, New Mexico 87113
Jason
Job Details:
09/18/2026
Installed control had same issuew but now no power coming from motor while running found loose connection at motor repaired connection unit operation checks ok. spoke to cx about review case#25003604
We serviced a
MAYTAG WASHER
Model MVW6200KW3
Near Central Point, Oregon 97502
Kyle
Job Details:
09/18/2026
"Customer states unit does not start. Ran cycle, unit will start, sense, and then go to done, found fault in capacitor and wire harness. Replaced capacitor and wire harness, tested machine on rinse and spin, unit is operating as intended."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF333SPS00
Near Breckenridge, Colorado 80424
Antonio
Job Details:
09/18/2026
Installed new cntrl and thermometer unit is cooling properly
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model GTS22KGNCRWW
Near Fruita, Colorado 81521
James R
Job Details:
09/18/2026
Signed disclaimers. Replaced L.F. and R.F. leg supports. Adjust feet so unit is tilted back some so doors swing shut with out much effort. Also noticed that the front of unit between F.F. and Frz was getting really hot. Slid unit out and removed cover over compressor. Found a dead mouse in the condenser fan. Removed it and condenser fan is running as designed. Please fill out tech satisfaction survey. Thank You.
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near Breckenridge, Colorado 80424
Antonio
Job Details:
09/18/2026
"Install new compressor and dryer. Then, charge the unit with R 600 unit is cooling properly"
We serviced a
SAMSUNG REFRIGERATOR
Model RF22R7551SR/AA
Near Colorado Springs, Colorado 80923
Brandon
Job Details:
09/18/2026
Found obstruction in fan removed and tested all checks ok svf paid $149.95 CC Auth# ML99MH
We serviced a
KITCHENAID RANGE
Model KSGS330SPS0
Near Breckenridge, Colorado 80424
Antonio
Job Details:
09/18/2026
Installed new cntrl board and fan then heated oven to 350?and unit is working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRSC5536RZ00
Near Rio Rancho, New Mexico 87144
Larry
Job Details:
09/18/2026
Installed IM and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM8
Near Rio Rancho, New Mexico 87144
Larry
Job Details:
09/18/2026
CX complaint - Leaving a chalky residue on the plates after cycle tried using vinegar and clean cycle but nothing - Inspected unit and found the rinse aid dispenser clogged - Cleared dispenser and tested good - Unit is good to go - Survey mentoined
We serviced a
FRIGIDAIRE RESIDENTIAL REFR
Model GRFS2853AF
Near Pueblo, Colorado 81006
David
Job Details:
09/18/2026
"Installed icemaker, ran diagnostics, tested icemaker defrost, harvest, and fill. All good. Cx to monitor."
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA
Near Pueblo, Colorado 81006
David
Job Details:
09/18/2026
"Installed compressor, leak tested, evacuated and charged system. Ran HASS, it passed. Unit is cooling down."
We serviced a
KITCHENAID ICE MACHINE
Model KUID508ESS1
Near Albuquerque, New Mexico 87111
Jason
Job Details:
09/18/2026
spoke to techline they sugest removing evap thermistor from circuit to make unit do timed cycle instead of relying on evap sensor cut sensor ou unit operation checks ok case#25005451
We serviced a
GENERAL ELECTRIC DRYER
Model GFD55GSSN3WW
Near Pueblo, Colorado 81001
James
Job Details:
09/18/2026
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX988SIBM00
Near Colorado Springs, Colorado 80917
Earl
Job Details:
09/18/2026
"I install the new solenoid valve and tested.It unit is operating properly at this time , hopefully with no more leaks"
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Albuquerque, New Mexico 87111
Jason
Job Details:
09/18/2026
Installed control and ui panel ran dry cycle unit operation checks ok. spokle to cx about review
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507ESS01
Near Colorado Springs, Colorado 80921
Charles
Job Details:
09/18/2026
Replaced freezer fan assembly. Paid labor autho MTA43W
We serviced a
THERMADOR INDUCTION COOKTO
Model CIT367YG/01
Near Breckenridge, Colorado 80424
Erik
Job Details:
09/18/2026
INSTALL COOK TOP GLASS* SEE QUICK PICSJOB COMPLETE
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
09/18/2026
Installed control board ran tests and calibration runs all ok
We serviced a
MAYTAG DRYER
Model MDG5500AWW
Near Colorado Springs, Colorado 80920
Torrey
Job Details:
09/18/2026
Found no continuity on the glow ignitor. Owner wants to fix this himself.$149.95 CC Auth# UW4M4E.
We serviced a
WHIRLPOOL DRYER
Model WED6150PW0
Near Grand Junction, Colorado 81506
James R
Job Details:
09/18/2026
Signed disclaimers. Checked for error codes. None. Checked air flow. Removed the lint screen and then put a paper towel in where it goes when start unit it blows back out. Which shows a restriction. When vent is disconnected the paper towel tries to go down into the lint screen area so there is good air flow. This restriction obviously is causing the issue. Checked heat element can see where it got too hot. Replaced it and the cutoff. Customer needs to have this checked again. This definity is causing the iccue of taking too long to dry due to the lack of air circulation. Please fill out tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MTW6205RF0
Near Colorado Springs, Colorado 80923
Aaron
Job Details:
09/18/2026
"Removed and replaced ui control, programmed and tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ12
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
09/18/2026
"Low side line vibrating against condenser fan assembly, corrected and monitored, working well now. Fan replaced is working as designed. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW6157PB1
Near Roseburg, Oregon 97470
Chris
Job Details:
09/18/2026
Replaced the control board and gear case. Tested
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC636SPS00
Near Medford, Oregon 97504
Kyle
Job Details:
09/18/2026
"Customer states unit is making a noise anywhere from 10-15 minutes and then stopping. Tested unit in diagnostic mode, all ice makers, fans, compressor and air dampers tested good and not making noise, operating as intended. Advised customer to try and take a video when it happens and document it for potential return visit. No defect found, unit is operating as intended."
We serviced a
WHIRLPOOL WALL OVEN
Model WOEC7030PZ01
Near Grand Junction, Colorado 81507
Clint
Job Details:
09/18/2026
Customer signed disclaimer and recived parts ordered.pulled unit out and replaced controls. Double checked to make sure the model number and control were the same. Unit is working perfectly. Customer will be checking to see if the time stays the same it will go off 3 hours.PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
SAMSUNG DISHWASHER
Model DW80R2031US/AA
Near Colorado Springs, Colorado 80915
Brandon
Job Details:
09/18/2026
"Found leak at hot water valve under sink dripping even with water valve turned off, recommend a plumber to replace valve and dishwasher supply line"
We serviced a
WHIRLPOOL WASHER
Model WTW4100SW0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
09/18/2026
"Removed and replaced valve, tested unit through diagnostics, working well now, no leaks. Advised customer of 5 star survey."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2323ASC
Near Bend, Oregon 97702
Levi
Job Details:
09/18/2026
Replaced evaporator fan motor tested and all checks okay
We serviced a
KITCHENAID RANGE
Model KSIS730PSS1
Near Ashland, Oregon 97520
Kyle
Job Details:
09/18/2026
"Customer states unit is locking control, and then displaying error code 03 after unlocking. Found code for E3 in tech sheet, states soft code for temp high on induction, caused by not enough fluid in pan, or an object upstrecting buttons, reset breaker and tested all burners. Unit is operating as intended"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
09/18/2026
Installed control board ran test and calibration all ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRTX5419SW00
Near Palisade, Colorado 81526
Clint
Job Details:
09/18/2026
Customer signed disclaimer and received parts ordered. Removed icemaker and water valve. Installed new icemaker and water valve .icemaker filled with water immediately no leaks found at water valve or connections.The old hose had a crack where it goes into the fill tube causing leak.PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL WASHER
Model WTW6157PW0
Near Grand Junction, Colorado 81504
Sean
Job Details:
09/18/2026
verified information & the customer signed disclaimer.checked the unit . The customer turned the unit on and it didn't start filling.I turned the water off at the valve and unhooked the water lines and tested the valves and looked at the screens.reattached the water lines and tested the unit .the unit started to fill with water. put the unit into service mode and checked for any errors the unit had none. put the unit into automatic test mode and the unit passed all the tests. checked the unit level and found the unit was a little bit low on the left front side. I adjusted the leveling legs.started the unit on a regular wash and watched the unit fill up with water. the unit tested good.thank you we appreciate your thoughts and want to give you the best experience possible soplease go to our website and fill out a technician survey.your technician.Sean...
We serviced a
GE STACK UNIT
Model GUD24ESSM1WW
Near Palisade, Colorado 81526
Sean
Job Details:
09/18/2026
verified information customer signed disclaimer.put the unit into services mode and checked for errors the unit had OBB . leveled the unit and put it through all testing. The unit passed testing and I recalibrated the pressure sensor. the unit is designed to only be locked in sensing and when the unit is spinning over 50 RPMs. it will be unlocked during wash and rinse .the unit tested good. operating as designed by factory.thank you.please fill out a technician survey.your technicianSean...
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Colorado Springs, Colorado 80915
Carlos
Job Details:
09/18/2026
Installed control board ran test and calibration al ok.
We serviced a
GE REFRIGERATOR
Model GWE22JYMCFFS
Near Breckenridge, Colorado 80424
Erik
Job Details:
09/18/2026
NO CROSS BAR STABILIZER IN FZ DRAWERCALL GE TAG: CONFIRM NO CROSS BAR ON THIS MODEL JOB COMPLETE
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFS2853AFM
Near Talent, Oregon 97540
Kyle
Job Details:
09/18/2026
"Replaced evap fan and fan blade, re assembled freezer. Plugged in unit and set to factory temps with freeze boost and chill boost selected. Advised customer to give 48 hours to reach temp, and to not open freezer door due to door gasket needing to reseal to unit. Unit operating as intended."
We serviced a
BOSCH DISHWASHER
Model SHP65DM5N/34
Near Colorado Springs, Colorado 80906
Briton
Job Details:
09/18/2026
INSTALL NEW POWER MODULE
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRFN2813AF6
Near Yoder, Colorado 80864
Earl
Job Details:
09/18/2026
"I installed the control board and the user interface, and the lights went out. When I closed the doors, it didn't bep and the length of time I was there, stating that the door was still open unit is operating properly at this time."
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW0
Near Redmond, Oregon 97756
Richard
Job Details:
09/18/2026
Installed new gear case rotor and clutch kit cycle tested unit all tested good at this time. Unit working as design job complete
We serviced a
WHIRLPOOL DISHWASHER
Model WDPS8024SZ1
Near Bend, Oregon 97702
Levi
Job Details:
09/18/2026
Replaced wash pump assembly tested all checks okay customer will finish install. No leaks found at time of service.
We serviced a
JENN-AIR MICROWAVE
Model JMW3430WS02
Near Colorado Springs, Colorado 80919
Briton
Job Details:
09/18/2026
REPLACED INVERTER AND MAG
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS07
Near La Pine, Oregon 97739
Levi
Job Details:
09/18/2026
"Replaced icemaker, tested, and all checks okay"
We serviced a
KITCHENAID REFRIGERATOR
Model KSRD25FKBL04
Near La Pine, Oregon 97739
Levi
Job Details:
09/18/2026
"Found small icecubes in the icemaker. Not sure if it a restriction in the water system or lack of use allowed the cubes to evaporate. Cleaned out ice maker and it started working and filled to proper level. Water filter was bypassed at some point in the past and may be a contributing factor. When flushing the water system, lots of whitish floaters were present. Icemaker appears to be working properly now."
We serviced a
JENNAIR REFRIGERATOR
Model JF36NXFXDE25
Near Pueblo, Colorado 81008
David
Job Details:
09/18/2026
"Checked refrigerator, upon arrival the fresh food evap fans were not running, put into diagnostics. When came out of diagnostics the fan motors started running. Control reset. Cx stated that he had not heard them running for some time. Cx to monitor."
We serviced a
KITCHENAID REFRIGERATOR
Model KUIX535HPS01
Near Grand Junction, Colorado 81501
James R
Job Details:
09/18/2026
Signed disclaimers. Unit is making ice. Replaced recirculation and drain pump. Finished assembling. Turned unit on and test operation fills and drains as designed. Recirculation pump is working great. Starting to cool and make ice. Please fill out tech satisfaction survey. Thank You.
We serviced a
BREDA DRYER
Model BRDV727001
Near Portland, Oregon 97201
Blake
Job Details:
09/18/2026
"KB 9/18Replaced heater element and confirmed unit powers on, spins, and heats. Previous install had a short loose vent connection due to the shape of the wall vent being oval and the ducting being round. informed customer this is an installation issue that will need to be resolved and is not part of the repair of the unit. Per customer request the duct was shaped and attached with two screws to hold where it should until install is corrected.Unit is functional, repair complete"
We serviced a
MAYTAG WASHER
Model MVW7232HW0
Near Grand Junction, Colorado 81503
James R
Job Details:
09/18/2026
Signed disclaimers customer indicated she had unplugged unit and plugged back in and has been working. Put into service diagnostics has a F2E2 error code. The only one cleared the error code. Then put thru a service diagnostics test. Could here some noise found coins between agitator and basket. Were badly worn. Also checked rotor the screw was loose at the same time inspected the stator and slider they are good. Re-tighten and put blue loctite on screw that holds rotor.Removed control panel and checked connections to it appear to be fine. Called tech line to confirm findings. Believe at this point that it may have been a pwr glich and unplugging cutting pwr reset the unit. Unit is working as designed. Please fill out tech satisfaction survey. Thank You. 25009162
We serviced a
GENERAL ELECTRIC WASHER
Model PTW600BSR1WS
Near Silverthorne, Colorado 80498
Erik
Job Details:
09/18/2026
INSTALL/ TEST: PASSJOB COMPLETE
We serviced a
ELECTROLUX REFRIGERATOR
Model 253.64702400
Near Colorado Springs, Colorado 80916
Brandon
Job Details:
09/18/2026
"Found bad defrost system ice build up on back wall, svf paid $149.95 CC Auth# PCRX4R"
We serviced a
BOSCH REFRIGERATOR
Model B36FD52SNS/01
Near Tigard, Oregon 97223
Blake
Job Details:
09/17/2026
"KB 9/17Documented the reoccurring error code 14 69 with Bosch TA. Support pushed the update to fix this issue to customers app account. If after the update is applied the issue persists, please call this number for further support 949-724-3746"
We serviced a
MAYTAG REFRIGERATOR
Model MRT311FFFH01
Near Redmond, Oregon 97756
Richard
Job Details:
09/17/2026
"Steamed drain out found restrictions @32 down the drain ,unable to remove restriction from drain called WHLP Tech support for resolution for repair and was turned over to resolution team for review.Case#24989018"
We serviced a
WHIRLPOOL WASHER
Model WTW4100SW0
Near Cloverdale, Oregon 97112
Brandon
Job Details:
09/17/2026
"install new motor, capacitor, and split H"
We serviced a
DACOR REFRIGERATOR
Model n/a
Near Colorado Springs, Colorado 80907
Briton
Job Details:
09/17/2026
"VALIDATED ICEMAKERS IN SELF TEST MODE, POWER CYCLED UNIT, POWER CYCLED ICEMAKERS AT UIREC CUSTOMER REPLACES WATER FILTER (SAMSUNG HAF-QIN) IF HOUSING NEEDS REPLACEMENT britonu@d3appliance.com - QUOTE 9/17/2026LABOR: Refrigerator / Ice Machine filter head or housing (Dacor ? HIGH end ? Tier 2) $295.95PART: Part (shipping incl.) $349.71SERVICE CALL $169.95MPS $18.50SALES TAX (CO Springs rate ? parts only ? 8.2%) $28.68TOTAL $862.79"
We serviced a
WHIRLPOOL WASHER
Model WTW5000DW3
Near Fountain, Colorado 80817
Briton
Job Details:
09/17/2026
"RE-ASSEMBLED CONTROL TOP, LOOSE ON R SIDENOTICED SLIGHT KNOCKING DURING HIGH SPIN, RAN CALIBRATION CYCLE- NO ERRORS IN DIAG LEVELED UNIT, SPOKE WITH CUST ABOUT COMPRESSION SLIDERS UNDER UNIT"
We serviced a
SAMSUNG RANGE
Model NE63A6511SS
Near Fountain, Colorado 80817
Briton
Job Details:
09/17/2026
REPLACED HI LIMIT
We serviced a
MAYTAG DRYER
Model MED7230HW
Near Colorado Springs, Colorado 80925
Briton
Job Details:
09/17/2026
REPLACED BLOWER AND MOTOR ASSM
We serviced a
KITCHENAID RANGE
Model KSDG950ESS8
Near Colorado Springs, Colorado 80919
Torrey
Job Details:
09/17/2026
Removed and replaced cooling fan. A lot more involved because the top and subpanel have to be removed to access the fan. Old fan was noticeably less free moving when spun by hand. Ran a bake cycle to test.
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS3
Near Colorado Springs, Colorado 80919
Torrey
Job Details:
09/17/2026
Removed and replaced sump. Check for leaks. Tested good. Contractor did not want to leave leak strip.
We serviced a
JENN-AIR REFRIGERATOR
Model JFFCC72EHL03
Near Monument, Colorado 80132
Torrey
Job Details:
09/17/2026
Removed and replaced icemaker. Cycle harvested and reads PA which is passed.
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF536RPS01
Near Colorado Springs, Colorado 80921
Torrey
Job Details:
09/17/2026
Removed and replaced ui. Tested good.
We serviced a
ASKO DISHWASHER
Model DB16641XXLS
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
09/17/2026
"replaced diverter and cover and unit checked okay, no one here to sign only the housekeeper and she does not own the home."
We serviced a
GE DRYER
Model GTD33EASK0WW
Near Pueblo, Colorado 81005
David
Job Details:
09/17/2026
"Replaced timer, tested and is operating correctly."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SG/AA
Near Pueblo, Colorado 81005
David
Job Details:
09/17/2026
"Installed water housing, ran water, working as designed"
We serviced a
SUB ZERO REFRIGERATOR
Model IT36CILH
Near Portland, Oregon 97202
Austin
Job Details:
09/17/2026
9/17/26 BA: removed and replaced ice maker. Did a manual harvest on the ice maker and its now producing ice. Service is complete $189.95 CC Auth# M4EXE9
We serviced a
ASKO DISHWASHER
Model BF1675PHXXLS.U
Near Hillsboro, Oregon 97124
Jesse
Job Details:
09/17/2026
"Screw found under unit, re secured a larger thread in its place for kick plate, verified tension springs are of normal operation volume. Client found door seal part in drain filter. Re secured. Per RE courtesy visit no charge."
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FFTR1814WW0
Near Bend, Oregon 97702
Levi
Job Details:
09/17/2026
"Found defrost timer was not advancing and would not enter defrost replaced the timer, tested and defrost is working good. Cleared evaporator of ice.; used 1 5304526183 (Defrost timer) from stock"
We serviced a
SAMSUNG M/W OTR
Model ME21DG6700SRAA
Near Central Point, Oregon 97502
Kyle
Job Details:
09/17/2026
"Replaced main control and door pcb, verified screen saver always on, tested unit, unit is operating as intended."
We serviced a
MIELE WASHER
Model W3033
Near Colorado Springs, Colorado 80904
Charles
Job Details:
09/17/2026
Replaced door boot
We serviced a
MAYTAG WASHER
Model MTW6200RW1
Near Edgewood, New Mexico 87015
Jason
Job Details:
09/17/2026
Installed control and lid latch and control ran calibration and quick cycle unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL REFRIGERATOR
Model WZF34X16DW10
Near Belen, New Mexico 87002
Larry
Job Details:
09/17/2026
Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
MAYTAG DRYER
Model MED7020RF0
Near Edgewood, New Mexico 87015
Jason
Job Details:
09/17/2026
Checked unit found console is bad. installed console unit operation checks ok. spoke to cx about review
We serviced a
BOSCH STEAM OVEN
Model HSLP451UC
Near Portland, Oregon 97215
Jesse
Job Details:
09/17/2026
Main board is not recognizing door switch Steam board is not sensing pitchers magnetic sensors movement. Corrosive white powder found within electrical board area.Parts are NLA. Referred to eastbank. Collected diag
We serviced a
SAMSUNG WASHER/DRYER COM
Model WD53DBA900HBA1
Near Pueblo West, Colorado 81007
David
Job Details:
09/17/2026
"Installed control and inverter, ran HASS, it passed."
We serviced a
GE REFRIGERATOR
Model GSS25LSLLCSS
Near Pueblo West, Colorado 81007
David
Job Details:
09/17/2026
"Replaced damper and sensors, cx is going to monitor."
We serviced a
THERMADOR DISHWASHER
Model DWHD640EFP/37
Near Winter Park, Colorado 80482
Erik
Job Details:
09/17/2026
ACCESS WITH BUILDERINSTALL DOOR PANELJOB COMPLETECX NOT AVAILABLE FOR SIGNATURE
We serviced a
ASKO DISHWASHER
Model ASK|DFI565XXL.U|7401
Near Basalt, Colorado 81621
Clint
Job Details:
09/17/2026
"Customer signed disclaimer and recieved part ordered. Installed new upper rails on dishwasher, old ones weren't stopping the basket from falling out. Unit was working properly. PLEASE TAKE TECH SURVEY THANKS.CLINT"
We serviced a
GE WASHER
Model GFW655SPV0DS
Near Winter Park, Colorado 80482
Erik
Job Details:
09/17/2026
CALL GE TAG: WHEN USING WHITES/ NORMAL CYCLES STEAM PREHEAT OCCURS FOR THE FIRST 15 MIN OF CYCLE * SEE QUICK PICS CX NOT ALLOWING ENOUGH TIME BEFORE TERMINATING CYCLE FOR FILL TO OCCURTEST: PASS/ CX EDUCATION ON CYCLE PERFORMANCEJOB COMPLETE
We serviced a
JENNAIR REFRIGERATOR
Model JBRFL36IGX
Near Winter Park, Colorado 80482
Antonio
Job Details:
09/17/2026
Found no issues or code unit is working properly
We serviced a
FRIGIDAIRE REFRIGERATOR
Model PRFC2383AFG
Near Fraser, Colorado 80442
Antonio
Job Details:
09/17/2026
Installed new thermometer and air tower unit is now cooling properly
We serviced a
CAFE DISH DRAWER
Model CDT845P2NBS1
Near Tabernash, Colorado 80478
Erik
Job Details:
09/17/2026
INSTALL/ TEST: PASSJOB COMPLETE
We serviced a
GE MICROWAVE
Model pvm9005sj8ss
Near Fraser, Colorado 80442
Erik
Job Details:
09/17/2026
CHECK ALL FUSES - MCB FAILURECX WILL REPLACE UNITJOB COMPLETE
We serviced a
ELECTROLUX DRYER
Model ELFE7637AT1
Near Aspen, Colorado 81611
Clint
Job Details:
09/17/2026
Customer signed discalimer and stated the dryer takes to long to dry.Dryer is heating and cycling fine the vent is clogged on the outside of the building and its on the second floor. They have a contractor who will climb up and clear it out.PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Aspen, Colorado 81611
Clint
Job Details:
09/17/2026
Customer signed disclaimer and stated the unit is not starting correctly. This is a new unit to them. I filled and drained it 3 times and sent a video to the property manager of it working...Please take tech survey thanks Clint
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Los Lunas, New Mexico 87031
Larry
Job Details:
09/17/2026
CX complaint - DW not powering on - Inspected unit and found a loose connection in the junction box - Secired wiring and tested good - Unit is good to go - Survey mentioned
We serviced a
WHIRLPOOL DISHWASHER
Model WDTA50SAKZ3
Near Albuquerque, New Mexico 87123
Jason
Job Details:
09/17/2026
Checked unit found ui is dead jason@d3appliance.com - QUOTE 9/17/2026TICKET # 587189LABOR: Dishwasher ? control panel (Whirlpool ? LOW end ? Tier 1) ? $189.95PART: ui panel (shipping incl.) ? $283.26SERVICE CALL ? $149.95MPS ? $18.50SALES TAX (ZIP 87123 ? parts 8.5% + labor 8.5%) ? $54.54TOTAL ? $696.20CX DOES NOT WANT TO REPAIR AT THIS TIME Auth code: YR3Y3J$162.70
We serviced a
WHIRLPOOL RANGE
Model WFGS3530RS0
Near Rio Rancho, New Mexico 87124
Larry
Job Details:
09/17/2026
CX complaint - Ovel not lighting - Inspected unit and found the igniter in the improperly positioned - Adjusted igniter and tested good - Unit is good to go
We serviced a
KITCHENAID RANGE
Model KSGS330SPS0
Near Albuquerque, New Mexico 87110
Jason
Job Details:
09/17/2026
Installed endcap unit operation checks ok. spoke to cx about review