We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ00
Near Vail, CO 81657
Antonio
Job Details: 10/23/2023
Flipped door seal unit tested good
We serviced a
KITCHENAID RANGE
Model KFDC506JSS01
Near Grand Junction, CO 81505
James R
Job Details: 10/23/2023
"Replaced the Appliance manager, User interface and temp sensor. Test operation in bake 400 degrees. Used digital thermometer. Temp went up to 400 degrees as should. Customer signed waiver. Please fill out whirlpool tech satisfaction survey. Thank You."
We serviced a
KENMORE WASHER
Model 110.26442502
Near Pueblo, CO 81005
James
Job Details: 10/23/2023
found rear leg adjusters out of alignment causing unit to go out of balance. adjusted and tested. all ops test good.
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Colorado Springs, CO 80911
Carlos
Job Details: 10/23/2023
"Ran test op. Readjusted agitator, ran a spin cycle grinning noise described by cx is gone, runs ok"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Colorado Springs, CO 80922
Aaron
Job Details: 10/23/2023
"Circulation motor is shorted out, removed and replaced Circulation motor assembly, tested unit and working well. No leaks, installed litmus strip. Advised customer of 5 star survey."
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, CO 80922
Aaron
Job Details: 10/23/2023
"Timer knob cracked, timer shaft worn, removed and replaced both parts, tested, working and heating well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJB00
Near Edwards, CO 81632
Antonio
Job Details: 10/23/2023
Installed acu door seal and filled water tray with water unit tested good
We serviced a
KITCHENAID REFRIGERATOR
Model KRSC700HPS
Near Eagle, CO 81631
Antonio
Job Details: 10/23/2023
Installed new water valves unit tested good
We serviced a
KITCHENAID DISHWASHER
Model KUDM01TJBL0
Near Colorado Springs, CO 80920
Glenn
Job Details: 10/23/2023
"Unit was filling with water w/o being turned on.Drain hose installed into its own separate drain & not tied into disposal? Possible water fill valve seeping water or not shutting off? Unit is not currently leaking any water into tub at this time, but it happened twice. Valve - WP8531669 $85.98 , Tax $7.05 , MPS $14.50 , Labor $189.95 , Suggest also replace heating element however, part is discontinued. Declined Estimate for now since everything is currently working and not leaking. Paid SC Fee of $129.95 , Autho# 49PJYW"
We serviced a
GE REFRIGERATOR
Model PYE22KYHNFS
Near Glenwood Springs, CO 81601
Erik
Job Details: 10/23/2023
Install water filter and educate CX
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Fountain, CO 80817
Carlos
Job Details: 10/20/2023
"Ran test op. Found door lock is bad. Replaced, ran 2nd test op runs all ok"
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW1
Near Edwards, CO 81632
Antonio
Job Details: 10/20/2023
"10/20/23 12:20: AG there 20 FRI, 12:19 to 12:19"
We serviced a
SAMSUNG M/W OTR
Model ME19R7041FS/AA
Near Colorado Springs, CO 80922
Mathew
Job Details: 10/20/2023
Picked up door to return to office.
We serviced a
WHIRLPOOL WASHER
Model WTW6120HW1
Near Edwards, CO 81632
Antonio
Job Details: 10/20/2023
"10/20/23 12:20: AG there 20 FRI, 12:19 to 12:19"
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Rifle, CO 81650
James R
Job Details: 10/20/2023
Printed labels. Took pic. Ready to send.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Albuquerque, NM 87121
Larry
Job Details: 10/20/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
GLADIATOR FREEZER
Model GAFZ30FDGB05
Near Monument, CO 80132
Glenn
Job Details: 10/20/2023
Install New Door supplied by customer.All OPS Test:OK
We serviced a
KITCHENAID RANGE
Model KSGB900ESS4
Near Colorado Springs, CO 80905
Glenn
Job Details: 10/20/2023
"range and oven fan not turning off makes loud noise.Adjust convection fan blades, as they were very close to back cavity. All OPS Test:OK, If problem returns, suggest order Cooling FAN-BLWR - W11107275"
We serviced a
KITCHENAID WALL OVEN
Model KOSE500EWH20
Near Monument, CO 80132
Glenn
Job Details: 10/20/2023
"CUST ONLY WANTS THE PARTS. SAID THAT THEY WILL INSTALL THEMSELVES. WE HOLD 0 LIABILTY IF THE UNIT IS STIL NOT WOKRING AFTER CX INSTALLATION. Model listed on ticket as KOSE500EWH > But actual Model is: KOSE500EWH20 , Dropped off parts, had customer sign."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Peyton, CO 80831
Aaron
Job Details: 10/20/2023
"Suspension worn, removed and replaced suspension, tested unit through diagnostics, working well now. Advised customer of 5 star survey."
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS20
Near Colorado Springs, CO 80906
Roman
Job Details: 10/20/2023
Installed element support. Put the microwave back together and made sure mw and oven are working properly. Working great.
We serviced a
BLUESTAR COOKTOP
Model RGTNB488BV2PLT
Near Colorado Springs, CO 80906
Roman
Job Details: 10/20/2023
Adjusted the spark harness and made sure connectors were I. Fully. Adjusted the burner and the clicking stopped.
We serviced a
WHIRLPOOL DRYER
Model WED560LHW2
Near Colorado Springs, CO 80908
Aaron
Job Details: 10/20/2023
"Unit pulled from cabinet and not properly wired upon arrival, terminal block nut stripped out, corrected wiring and testing unit, heating well now. Property vacant, unable to obtain signature or advise of survey."
We serviced a
CAFE REFRIGERATOR
Model CYE22UP2MKS1
Near Leadville, CO 80461
Erik
Job Details: 10/20/2023
install hot/cold tank and test: GOODNO LEAKS!JOB COMPLETE*leave leak strip detector (see quick pics)CX NOT HOME
We serviced a
WOLF STOVE
Model GR366
Near Colorado Springs, CO 80906
Jerimiah
Job Details: 10/20/2023
"Back out onsite, verified 1 pipe minus 4 inches of 3/4 goes to the stove, called techline, unit is now preheating without issue but reignition after preheat is a problem. Techline is saying theres nothing else to be done except call the utility co and ask for at least 9-11 pressure. Issue is wolf says bare minimum is 7 and we are at 7.5, but now saying its not guaranteed even after minimum is met. Cust will fight with utility to ask for increase."
We serviced a
JENN-AIR WALLOVEN
Model JJW2430DS01
Near Monument, CO 80132
Glenn
Job Details: 10/20/2023
"R & R New Console. Program to unit.All OPS Test:OK , Paid SC Fee of $169.95 + Labor $209.95 = $379.90 , Autho# AKTH3P"
We serviced a
AMANA REFRIGERATOR
Model ART308FFDB11 NO
Near Colorado Springs, CO 80915
Carlos
Job Details: 10/20/2023
"Installed compressor and charged, cx will observed"
We serviced a
GE RANGE ELECTRIC
Model JB735SP1SS
Near Peyton, CO 80831
Jerimiah
Job Details: 10/20/2023
"Installed replacement controller, unit check ok. Charged labor as quoted $189.95 CC Auth# PF9HV9"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Colorado Springs, CO 80908
Aaron
Job Details: 10/20/2023
"Removed and replaced gearcase, suspension, and slider assembly. Ran unit through DLMS and diagnostic cycles. Working well and no error codes. Advised customer of 5 star survey."
We serviced a
SAMSUNG WASHER
Model WA45T3200AW/A4
Near Colorado Springs, CO 80909
Mathew
Job Details: 10/20/2023
"Replaced lid switch, test op all okay. Unit not wireless hass compatible."
We serviced a
MAYTAG DRYER
Model MEDB855DC4
Near Colorado Springs, CO 80927
Mathew
Job Details: 10/20/2023
"Unit needs terminals, terminal blocks, power chord and repair kit. Cx not repairing, paid svf $129.95 $129.95 CK Auth# H9C449Svf $129.95 MPs $14.50Parts 279318 terminal 87.14WP3397659 block 57.154392067 repair kit 75.90Pt400L chord. 61.02 Parts total $281.21+23.06 Due today $448.72 Due on install Labor $219.95"
We serviced a
SUB ZERO WINE COOLER
Model 424HAG
Near Colorado Springs, CO 80906
Ralph
Job Details: 10/20/2023
insstalled part cust to monitor
We serviced a
TRAULSEN REFRIGERATOR
Model UR30WT-A
Near Colorado Springs, CO 80904
Ralph
Job Details: 10/20/2023
"unit was unplugged upon arrival, believe unit may have been iing over on the evap fn motor, and that was the fan blade most likely rubbing on the ice, cust to call back if issue resurfaces"
We serviced a
WHIRLPOOL DRYER
Model WHD560CHW2
Near Albuquerque, NM 87110
Jason
Job Details: 10/20/2023
Checked unit found temps check ok. found some lint acumulating in coils removed what i could get from front
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Colorado Springs, CO 80924
Mathew
Job Details: 10/20/2023
Replaced diffuser. Test op all okay.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ05
Near Clifton, CO 81520
James R
Job Details: 10/20/2023
Replaced icemaker. Test cycled. ok. customer paid cash. I kept but billed out to my card. auth code M3U3N4
We serviced a
MAYTAG WASHER
Model MVW4505MW0
Near Grand Junction, CO 81501
James R
Job Details: 10/20/2023
Replaced capacitor. W11395618 Also belt is loose replaced W11239857 Put into service diagnostics. No error codes when done. customer signed waivers. Put a leak board under unit. Please fill out whirlpool tech satisfaction survey. Thank You. ; used 1 W11239857 (Belt) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ03
Near Colorado Springs, CO 80907
Carlos
Job Details: 10/20/2023
7737545438 Called tech line. No more correction actions to be take about the humming from compressor. In is normal. Ice maker runs harvest cycle ok. Cx needs to observe ice maker.
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Colorado Springs, CO 80924
Aaron
Job Details: 10/20/2023
"Removed and replaced support, working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ0
Near Colorado Springs, CO 80918
Glenn
Job Details: 10/20/2023
"Install New Sump & Motor Assy, All OPS Test:OK, No Leaks, Installed Leak detector for safety. Informed customer about suvey."
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF507HPS02
Near Grand Junction, CO 81507
James R
Job Details: 10/20/2023
Water pressure to home is 60 PSI good. Replaced water valve behind unit. Had replaced water valve up in F.F. area before. Unit has good water flow. Customer says that it didnt make the noise until they replaced filter. I removed filter and dispensed water again has same sound which sounds normal to me. Reinstalled filter and dispensed water again sounds the same. dispensed with tech on phone said sounds normal as well. SR# 7737605101 Had customer sign waivers. Put leak board under unit. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Grand Junction, CO 81507
James R
Job Details: 10/20/2023
Replaced all 4 dampner shocks. Greased connection points. Reassembled test run in service diagnostics test 12 operating as should. No error codes when finished. Vibration is minimal empty. Normal. Unit is level and feet are solid on floor. customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Albuquerque, NM 87120
Larry
Job Details: 10/20/2023
Installed parts listed and tested good - Unit is good to go - Also secured wires at bottom of door because they were clicking wehn the door was opened - Explained other noises are normal
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Fruita, CO 81521
James R
Job Details: 10/20/2023
"Replaced gearcase spins much quieter. Calibrated unit, did a unbalanced detection ok. Put thru a service diagnostics test good no codes. In spin. Back panel though rattles alot. Adjusted so fits tighter adgainst frame. Put into high speed spin. Made a big difference. Adjusted feet to floor. Put a leak board under unit. Customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You."
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Albuquerque, NM 87114
Larry
Job Details: 10/20/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Rio Rancho, NM 87124
Larry
Job Details: 10/20/2023
CX complaint - Dryer not heating - Inspected unit and gounf the therm open - Replaced with TS and tested good - Unit is good to go; used 1 W10900067 (CUTOFF-TML) from stock
We serviced a
AMANA DRYER
Model NED4655EW1
Near Albuquerque, NM 87110
Jason
Job Details: 10/20/2023
"CHECKED UNIT FOUND LOOSE CONNECTION TO TIMER, REPAIRED CONNECTION UNIT CHECKS OK"
We serviced a
KITCHENAID REFRIGERATOR
Model KSSO48QTB03
Near Albuquerque, NM 87122
Jason
Job Details: 10/20/2023
installed parts listed unit checks okAuth code:9344LN$206.10
We serviced a
WHIRLPOOL DRYER
Model MED7230HW2
Near Rio Rancho, NM 87144
Larry
Job Details: 10/20/2023
Installed parts listed and tested good - Unit is good to go
We serviced a
WHIRLPOOL WASHER
Model WTW7120HW0
Near Albuquerque, NM 87111
Jason
Job Details: 10/20/2023
SR7737604729Spoke with Techline about issue they are contacting engineering and resolution department to get issue resolved they will be contacting us and cx in the future with resolution
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Rio Rancho, NM 87144
Larry
Job Details: 10/20/2023
Installed parts listed and tested goo d- Unit is good to go
We serviced a
MAYTAG DRYER
Model MED8630HC2
Near Albuquerque, NM 87111
Jason
Job Details: 10/20/2023
checked unit found element open installed element unit checks ok; used 1 WP3387747 (element) from stock
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS08
Near Corrales, NM 87048
Larry
Job Details: 10/20/2023
Installed switch and gasket and tested good - Unit is good to go
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JS1
Near Colorado Springs, CO 80924
Aaron
Job Details: 10/20/2023
"Left side of oven door is protruding further than the right. Removed and replaced hinges, door is closing evenly, verified by customer. Advised customer of 5 star survey."
We serviced a
SAMSUNG WASHER
Model WA48H7400AP/A2
Near Colorado Springs, CO 80925
Brandon
Job Details: 10/20/2023
"Cx complaint: not filling enough, I tested fill on heavy, normal and light, unit is filling to spec, pressure sensor tests ok at 25hz and drops according to soil level selected, no issues found"
We serviced a
SAMSUNG WASHER
Model WA45T3200AW/A4
Near Pueblo, CO 81001
Brandon
Job Details: 10/20/2023
"Found belt off unit, put belt back on and leveled unit, tested op all hass passed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF263BEAESG/AA
Near Pueblo, CO 81005
Brandon
Job Details: 10/20/2023
Replaced parts and tested op all ok hass not compatible
We serviced a
WHIRLPOOL DISHWASHER
Model KDFE204KPS0
Near Fountain, CO 80817
Carlos
Job Details: 10/20/2023
7737601809 Installed water assembly. Cx needs a plumber to turn down water pressure of the hot water for dishwasher
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC0
Near Colorado Springs, CO 80922
Mathew
Job Details: 10/20/2023
"Replaced lid switch, control and drain pump. Test op all okay."
We serviced a
GE DISHWASHER
Model GDT655SMJ0ES
Near Fountain, CO 80817
James S
Job Details: 10/19/2023
PCB is malfunctioning and not receiving power.SC- 129.95Pcb - $227.96RL - 189.95Auth# PVEUU9
We serviced a
SAMSUNG WALLOVEN
Model NV51K7770DS/AA
Near Monument, CO 80132
Jerimiah
Job Details: 10/19/2023
Reinstalled eeprom board connector. Unit check ok
We serviced a
WOLF RANGE
Model DF48650G/S/P
Near Monument, CO 80132
Jerimiah
Job Details: 10/19/2023
"Unable to locate dent, Will need either two people or air sled to uninstall unit and check for anything on back of unit, closing call."
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Rifle, CO 81650
James R
Job Details: 10/19/2023
Labels printed and took pics. Ready to send.
We serviced a
KITCHENAID MICROWAVE
Model KOCE500ESS11
Near Monument, CO 80132
Jerimiah
Job Details: 10/19/2023
"Unit microwave cavity light not lighting, could hear unit clicking relay but would not run, could only keep time. Found bad melted wiring on top MW. Repaired. Unit check ok, charged service call. $136.45 CC Auth# 9WENHU"
We serviced a
WHIRLPOOL DRYER
Model MED7230HW1
Near Peyton, CO 80831
Aaron
Job Details: 10/19/2023
"Heating element shorted out, shorted thermal fuse as well, rest of unit is in good condition. Approved on site. Removed and replaced parts and tested unit, heating well now. Element wp3387747 $99.68Thermal fuse w10909685 $89.60Total parts $189.28Tax $15.52Supplies $14.50Hc $149.95Labor $199.95Total job $569.20Approved on siteNo return on parts Auth total due $569.20 #T4EE4K"
We serviced a
MAYTAG WASHER
Model MVWC416FW1
Near Colorado Springs, CO 80907
Carlos
Job Details: 10/19/2023
"Ran test op runs ok. Cx education, cx was not aware that Deep Fill does not function while using Normal cycle per owners manual."
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Colorado Springs, CO 80918
Glenn
Job Details: 10/19/2023
"f2e2 not working at all , Install New UI Control. All OPS Test:OK"
We serviced a
JENNAIR WALL OVEN
Model JMW2430LL02
Near Monument, CO 80132
Glenn
Job Details: 10/19/2023
Install New Element Support in MW ceiling. All OPS Test:OK
We serviced a
WHIRLPOOL RANGE
Model WFG525S0JS2
Near Monument, CO 80132
Jerimiah
Job Details: 10/19/2023
"Griddle burner was not fully igniting around head, took apart, cleaned burner head and cap, unit check ok. Unit under warranty per WP Cust service, piced."
We serviced a
VIKING RANGE
Model LDSC485-6GBK
Near Peyton, CO 80831
Jerimiah
Job Details: 10/19/2023
Installed replacement igniter switch. Unit check ok. Charged labor as quoted $208.95 CC Auth# 3NWJJ3
We serviced a
SAMSUNG WALLOVEN
Model NV51K6650DS/AA
Near Colorado Springs, CO 80924
Brandon
Job Details: 10/19/2023
"No errors, found loose connections on main pcb, reseated connections and tested op all ok test to 250 both top and bottom both heating"
We serviced a
SAMSUNG DRYER
Model DV448AEP/XAA
Near Colorado Springs, CO 80920
Brandon
Job Details: 10/19/2023
Replaced parts and tested op all okCollected remaining due $294.78 Auth# JYHY9Y
We serviced a
SAMSUNG REFRIGERATOR
Model RFG237AARS/XAA 03
Near Colorado Springs, CO 80904
Brandon
Job Details: 10/19/2023
Replaced parts and tested op all fans working checked at main board all okCollected tax for parts $7.66
We serviced a
SAMSUNG REFRIGERATOR
Model RF261BEAESR/AA
Near Colorado Springs, CO 80919
Brandon
Job Details: 10/19/2023
"Replaced condenser fan and tested op all ok, waited for temps to drop, unit is cooling Labor paid (check) $189.95 Auth# X399AT"
We serviced a
JENNAIR WALL OVEN
Model JMW2430DP03
Near Elbert, CO 80106
Aaron
Job Details: 10/19/2023
"Removed and replaced UI control, programmed and tested, working well. Advised customer of 5 star survey."
We serviced a
SUB ZERO REFRIGERATOR
Model 700br
Near Colorado Springs, CO 80906
Ralph
Job Details: 10/19/2023
"installed parts and cust to monitor....THIS REPAIR WAS DONE AS A WARRANTY ON THE LABOR, DISREGARD STICKY ON 795.00 LABOR, TRAVIS APPROVED"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Colorado Springs, CO 80906
Roman
Job Details: 10/19/2023
Ran fridge through diagnostics and no error codes or noises coming from the fridge. Checked all fans and compressor. Could not get lights to flicker all seem to be working okay. Fridge working great. If problems continue call us back and we should order a control board.
We serviced a
GE RANGE
Model JBS86SP5SS
Near Colorado Springs, CO 80904
Roman
Job Details: 10/19/2023
"Ran the oven and and breaker trips, after about 5 minutes. Doesnt seem to have a specific time that breaker trips and doesnt happen right away indicating something is wrong with range. Called tech line and checked amperage and oven pulled 2.2 amps and tripped. Recommend calling a electrician .case number #11117323"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, CO 80905
Carlos
Job Details: 10/19/2023
"Installed lid lock, ran test op runs ok"
We serviced a
SCOTSMAN ICE MACHINE
Model SCCP30MA-1SU
Near Colorado Springs, CO 80904
Jessie
Job Details: 10/19/2023
Replaced bin t Stat. Customer said techline told me.to male.a high altitude adjustment. Did as instructed. Leak strip under unit.
We serviced a
SUB ZERO REFRIGERATOR
Model BI48SIDSPH
Near Colorado Springs, CO 80908
Jessie
Job Details: 10/19/2023
Replaced freezer compressor and light bar. Charged unit 134a 5.5 ounce. Ran diagnostics and monitored the unit. All ok
We serviced a
WHIRLPOOL WASHER
Model WTW5300SQO
Near Colorado Springs, CO 80911
Carlos
Job Details: 10/19/2023
Cx needs a plumber to unclog drain for washing machine. Cx paid SC $129.95 CK Auth# NNP4YW
We serviced a
SAMSUNG RESIDENTIAL REFR
Model RF23J9011SG/AA
Near Colorado Springs, CO 80920
Mathew
Job Details: 10/19/2023
"Replaced auger motor, unit now dispensing full ice cubes. All test ok."
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Pueblo, CO 81004
David
Job Details: 10/19/2023
"Checked heater, thermostats, all good Verified voltages at wall, one leg has 120 volts, the other has 40 volts, across the 2 hots it is 70 volts. Tried resetting breaker, still the same.One side of the breaker does not feel like it is resetting. Took pics of the voltages on meter"
We serviced a
GENERAL ELECTRIC RANGE
Model PS960SL2SS
Near Pueblo, CO 81005
David
Job Details: 10/19/2023
Replaced Upper oven sensor Tested and working good No error codes
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDW10
Near Pueblo, CO 81005
David
Job Details: 10/19/2023
Checked refrigerator Fill tube for icemaker was not fully going into the Fill cup of the icemaker Repositioned tube and is working good
We serviced a
WHIRLPOOL RANGE
Model WEG745H0FS0
Near Colorado Springs, CO 80919
Glenn
Job Details: 10/19/2023
"f8e0 error code = Cooling Fan Speed Too LowBlower - W11107275 $139.62 , Tax $11.45 , MPS $14.50 , Labor $229.95 , Paid in Full $545.47, Autho# 34UVK4"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Calhan, CO 80808
Aaron
Job Details: 10/19/2023
"Removed and replaced suspension and valve, tested unit and working well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0HS04
Near Albuquerque, NM 87110
Jason
Job Details: 10/19/2023
installed console and control unit checks ok
We serviced a
JENN-AIR WALLOVEN
Model JJW2830DS01
Near Albuquerque, NM 87122
Jason
Job Details: 10/19/2023
installed console unit opperation checks okAuth code:3MHXRV$336.25
We serviced a
KITCHENAID WALLOVEN
Model KOCE507ESS22
Near Albuquerque, NM 87112
Jason
Job Details: 10/19/2023
installed support unit checks ok
We serviced a
GLADIATOR FREEZER
Model GAFZ30FDGB04
Near Edgewood, NM 87015
Jason
Job Details: 10/19/2023
installed control and sensor unit checks ok
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ04
Near Silt, CO 81652
James R
Job Details: 10/19/2023
Thawed out evaporator. Replaced heater and evaporator thermistor. Put a plastic tie around thermistor and silver tape around it help keep in place. Replaced electronic control. Unit started up and is cooling. Customer signed waivers. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MVW6230HW3
Near Pueblo West, CO 81007
David
Job Details: 10/19/2023
"Checked washer Ran through diagnostics cycle, no error codes Ran a quick wash Running like it is designed"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351SG/AA 00 RF
Near Colorado Springs, CO 80918
Brandon
Job Details: 10/19/2023
"Replaced parts, sealed ice room and tested op all ok"
We serviced a
MAYTAG WASHER
Model MVW7230HC1
Near Albuquerque, NM 87105
Larry
Job Details: 10/19/2023
Installed Lower harness and teted good - Unit ia good to go
We serviced a
SAMSUNG REFRIGERATOR
Model RF263TEAESG/AA
Near Colorado Springs, CO 80911
James S
Job Details: 10/19/2023
Replaced PCB. Unit is making ice with zero ice build up. Could not run HAAS.Attached screenshot of HAAS
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDM09
Near Colorado Springs, CO 80919
Glenn
Job Details: 10/19/2023
"Install New Door Gasket on FF Door, Adjust Frzr Gasket. All OPS Test:OK"
We serviced a
MAYTAG DRYER
Model MED5630HC2
Near Carbondale, CO 81623
James R
Job Details: 10/19/2023
"Started unit hear a rattling noise. Checked back pressure of venting of home. .46 good is within specs. run on regular cycle high temp more dry. No cloths in unit. Ran awhile did sense Then shut down. Normal. Next put some wet towels in unit. Sensing light came on. Towels are touching the moisture sensing bars. Now is indicating the towels are wet. Now is indicating cool down. Shut down checked towels completely dry. Also must dry like items. linens and sheets if dried with towels or any cottons will dry quicker and if these are what touch the sensing bars unit will shut down thinking load is dry. Leveled and raised unit so even with washer. Replaced all supports, ok.Normal to a a thump due to the seem in the drum.Can here a loud vibration. Removed motor put silver tape under it. ; used 4 W10314173 (Support) from stock"
We serviced a
WHIRLPOOL WASHER
Model WET4027HW0
Near Aspen, CO 81611
James R
Job Details: 10/19/2023
"F7E6 motor fault. Cleared code. Put into automatic test went thru just fine no errors when done. Put unit thru a quick wash. Did just fine. Inspected belt, drive pulley and actuator all look good. Everything is tight pulley shield is in good shape has not been rubbing. Fills, agitates, drains and spins. Operating as should. Customer signed waivers.Please fill out whirlpool tech satisfaction survey. Thank You. Customer paid Service call $209.00 auth code 4Y3MT3"