We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ13
Near Fruita, Colorado 81521
James R
Job Details:
03/30/2026
"Signed disclaimer. Checked ice chute door it is closing and opening all the way, As well closes slowly as should. Took pic of issue sent to tech. Customer is using crushed need to use cubed to help clear out and it is commom for when using crushed for ice residue to build up. Need to keep it cleaned out. Ice in tray is not bridged. So icemaker does not appear to be over filling. Cubed ice can at times come out to quickly and hang up need to clear it out. Removed ice clump from chute area and dispensed ok. There are no further reccomendations for repair. Will need to contact customer care going forward. 23035896"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT531HAPM0
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/30/2026
Arrived and cx complaint of smell . Took dw out of cabinets ran with unit out. No leaks no smell. Cx has had plumbing issues in wall. Plumbers are coming to fix pipes. Dw is functioning as designed. No further issues noted. Informed cx of review process.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRMF3636RZ00
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
03/30/2026
Ice Maker producing ice properly all ok
We serviced a
GE WASHER
Model GFW655SPV0DS
Near Fruita, Colorado 81521
Sean
Job Details:
03/30/2026
Verified information & customer signed disclaimer.Unplugged the unit and removed the UI and top panel.Removed the controller. And installed the new one.Reassembled the unit and turned it on. Set up the programming. And tested the unit.The unit door locks and the unit runs through the cycle.Tested the unit good.
We serviced a
KITCHENAID DISHWASHER
Model KDTS324SPS0
Near Colorado Springs, Colorado 80904
Carlos
Job Details:
03/30/2026
Installed bolt latch ran tests runs all ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Colorado Springs, Colorado 80909
Carlos
Job Details:
03/30/2026
Unit runs all designed called techline 23047621 cx needs to use rinse aid
We serviced a
GENERAL ELECTRIC WASHER
Model GFW655SPVDS
Near Colorado Springs, Colorado 80922
Earl
Job Details:
03/30/2026
Install the new parts and test of the unit unit is operating properly at this time
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRQC7836RZ00
Near Rio Rancho, New Mexico 87144
Tye
Job Details:
03/30/2026
Arrived and cx complaint of not dispensing water. I removed filter and water started dispensing. Re Installed filter. Water is working now. Informed cx of possible cheap filter.. advised to buy directly from whirlpool. No further issues noted
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Monument, Colorado 80132
Charles
Job Details:
03/30/2026
Replaced control board and started cycle
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80909
Carlos
Job Details:
03/30/2026
Installed control board runs all ok
We serviced a
WOLF RANGE
Model IR36551/S/P
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
03/30/2026
INSTALLED PART AND UNIT CHECKED OKAY
We serviced a
ELECTROLUX DOUBLE WALL OVEN
Model EW30EW65GS8
Near Colorado Springs, Colorado 80921
David
Job Details:
03/30/2026
"Pulled out oven, upper oven thermal tripped, reset resetable the thermal, tested and oven is heating."
We serviced a
MIDEA REFRIGERATOR
Model MRT18D3BWW
Near Pueblo, Colorado 81004
James
Job Details:
03/30/2026
Found temps ok compressor running normally adjusted damper to allow less air into freezer. See attached pictures and notes
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2323ASC
Near Pueblo, Colorado 81006
James
Job Details:
03/30/2026
Installed ordered evap fan tested ops all ckok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRMF3636RZ00
Near Pueblo, Colorado 81001
James
Job Details:
03/30/2026
Found unit making ice on arrival. Water and fans working as designed replaced preordered ice maker and valve tested ops all ckok
We serviced a
BOSCH REFRIGERATOR
Model B36CT80SNB
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
03/30/2026
"found a drawer not installed correctly which was holding up the door, remedied the issue"
We serviced a
MAYTAG DRYER
Model MGD4500MW1
Near Delta, Colorado 81416
Sean
Job Details:
03/30/2026
"Verified the unit information customer signed disclaimer.Pulled the unit out and removed the backTop and door panel, checked the unit igniter.It was cracked. Installed the new igniter and replaced the coil.Reassembled the unit and tested .The unit starts and heats up.Found no additional problems with the unit.Thank you."
We serviced a
HOTPOINT REFRIGERATOR
Model HTS18CBSALCC
Near Colorado Springs, Colorado 80907
Ralph
Job Details:
03/30/2026
"cleared the drain line, uniy checked okay...autho no. 94uu4p"
We serviced a
MAYTAG DRYER ELECTRIC
Model MED6630MBK0
Near Colorado Springs, Colorado 80922
Aaron
Job Details:
03/30/2026
"Heating element is shorted out, removed and replaced, lubricated rollers and idler, tested unit, working and heating well now."
We serviced a
MAYTAG WASHER
Model MTW6205RW1
Near Grand Junction, Colorado 81503
James R
Job Details:
03/30/2026
Signed disclaimer. Replaced gearcase DLMS calibrated it and then ran thru a service test is operating as designed. Please fill out tech satisfasction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MVW6200KW5
Near Albuquerque, New Mexico 87121
Larry
Job Details:
03/30/2026
CX complaint - Washer wont dispense softener and conplete cycle - Inspected unit and found the cold water supply was turned off because the valve leaks - xplained to CX that the machine must have a cold water supply to operat correctly - Tested unit with cold water on and tested good - Unit is good to go - Survey mentioned
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Rifle, Colorado 81650
Clint
Job Details:
03/30/2026
Customer signed disclaimer and recieved lid switch ordered.installed new lid switch ran the unit on speed wash and is running perfectly...PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Grand Junction, Colorado 81504
James R
Job Details:
03/30/2026
Signed disclaimer. Unit is not draining as well. Unit was too full. Found some stuff in drain pump. Cleaned out. Replaced door seal. Removed outer door Run unit and did not leak. Put a leak board under unit and took pic.Please fill out tech satisfaction vsurvey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Pueblo, Colorado 81008
James
Job Details:
03/30/2026
Installed preordered part tested ops all ckok
We serviced a
GE RANGE
Model GGF400PVSS
Near Fountain, Colorado 80817
Ralph
Job Details:
03/30/2026
"TURNED UNIT UP TO 450 AND SAW NO SIGNS OF SMOKE, UNIT IS VENTING CORRECTLY, CUST TO MONITOR, BUT CURRENTLY UNIT WORKING AS INTENDED"
We serviced a
MIELE COFFEE MACHINE
Model CVA6805
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
03/30/2026
"showed cust how to blow out the grounds chute, unit made a nice batch of coffee...autho no.T9P9C9"
We serviced a
KITCHENAID WALL OVEN
Model KOCE500EBS09
Near Monument, Colorado 80132
Jason
Job Details:
03/27/2026
"Visually inspected unit and wiring, adjusted 240 line to prevent sound echoing, ran test mode and verified functionality of all components, broil convect was ran, no other issues found. Spoke with whirpool safety"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ00
Near Peralta, New Mexico 87042
Larry
Job Details:
03/27/2026
Installed controls and tested good - Unit is good to go
We serviced a
JENN-AIR DOUBLE WALL OVEN
Model JMW3430LL02
Near Monument, Colorado 80132
Jason
Job Details:
03/27/2026
"Unit fell off oven dolly when diagnosing. After resetting the breaker for 5 minutes and then after testing all components when the unit finally had power, there were no issues other than a UI miscommunication error and a stuck keypad error from 2 years ago. Spoke to Rick about a dent in the floor me and the customer found that there was one more small dent in the cabinet, send photos to Rick, Man the customer found no other issues of oven is now working"
We serviced a
MAYTAG RANGE
Model MER4800PZ1
Near Medford, Oregon 97501
Kyle
Job Details:
03/27/2026
"Found right front burner with short on element, found switch loose in contacts inside switch. Replaced burner switch, burner element and tested. Unit operates as intended"
We serviced a
SAMSUNG RANGE
Model NSE6DG8700SRAA
Near Ashland, Oregon 97520
Kyle
Job Details:
03/27/2026
"Replaced all 4 burner switches and tested. Unit is operating in all cycles, low, medium, and high on all burners. Unit operating as intended."
We serviced a
MAYTAG WASHER
Model MVW6200KW3
Near Ashland, Oregon 97520
Kyle
Job Details:
03/27/2026
"Gear case leaking excessively. Replaced gear case, motor, actuator, harness, capacitor, splutch kit and belt. Tested unit in quick wash cycle and drain ans spin. Unit is operating as intended."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, Colorado 80910
Earl
Job Details:
03/27/2026
"I installed the new control board and ran it into a calibrate , tested it in a cycle unit is operating properly at this time"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model GRFG2353AFG
Near Redmond, Oregon 97756
Richard
Job Details:
03/27/2026
Installed new user interface cycle tested all tested fine at time of repair
We serviced a
LG REFRIGERATOR
Model LMX30995ST/01
Near Colorado Springs, Colorado 80907
Charles
Job Details:
03/27/2026
Replaced ice maker assembly
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Cimarron Hills, Colorado 80915
Carlos
Job Details:
03/27/2026
Installed control board ran test and calibration all ok
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LS2
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
03/27/2026
Recorded all data points
We serviced a
BOSCH DISWASHER
Model SGE53X52UC/63
Near Palisade, Colorado 81526
Sean
Job Details:
03/27/2026
Verified the information customer signed disclaimer.Opened the unit and unplugged it.Removed the door panel and controller. Removed the control board from the controller and installed the new one. Removed the soap dispenser and installed the new one .Reassembled the unit . Leveled it again and installed it.Ran the unit on a rinse cycle found no leaks .After the cycle I opened the unit and filled up the rinse aid container with what was left in old one.The unit tested good .It is operating as designed by factory.The unit needs to have the rinse aid filled up.There was not enough in the old one to fill and found none under sink.
We serviced a
VIKING DOWNDRAFT VENT
Model VIPR181RSS
Near Colorado Springs, Colorado 80904
Charles
Job Details:
03/27/2026
"No lights/not functional, removed drawers, removed access panel, voltage at outlet good, pulled up touchpad, got dc voltage, clean touchpad connection, reconnected power, unit working. Customer requested leave touchpad up so they can clean and silicone back to counter. Service fee$169.95, Labor $219.95, Total 389.90 paid autho 393HRH"
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW1
Near Breckenridge, Colorado 80424
Antonio
Job Details:
03/27/2026
Installed new acu then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Fruita, Colorado 81521
Clint
Job Details:
03/27/2026
Customer signed disclaimer and recieved control board ordered. Installed new control.ran unit through diagnostic check everything checked ok. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ19
Near Parachute, Colorado 81635
Clint
Job Details:
03/27/2026
Customer signed disclaimer and recieved parts ordered installed new fan and shroud unit sounds better. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
PROFILE REFRIGERATOR/TOP
Model PVD28BYNHFS
Near Grand Junction, Colorado 81507
Sean
Job Details:
03/27/2026
Verified the unit information and customer signed disclaimer. Opened the freezer compartment and removed the shelves and the back panel. Unplugged the fans and removed fan. Installed the new fan into the unit and hooked it back up.Reassembled the unit . Tested and the fan came on and started cooling the ice maker compartment. Tested the unit good. The ice maker will take a few hours to stabilize and start making ice.Turned the ice maker on.
We serviced a
WHIRLPOOL RANGE
Model WEE515S0LS2
Near Colorado Springs, Colorado 80903
Carlos
Job Details:
03/27/2026
Recorded all data points
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
03/27/2026
Installed control board ran test and calibration runs all ok
We serviced a
WHIRLPOOL RANGE
Model WFES4530SZ0
Near Grand Junction, Colorado 81507
James R
Job Details:
03/27/2026
Customer indicated that oven cooks too hot. Started unit set to 400 degrees. Put a temp meter in unit checked oven temp. Is running to hot gets up to 439 degrees and drops to 405 then cycles back up. Did a oven calibration off set -20 degrees. Watched temp hi and low. Now cycles as should. Showed customer how to do a offset. Also can hear right hinge making a popping noise. Removed and reinstalled door and it quit making the noise. Also indicated that they believe surfaces are getting too hot and on the outer glass door. Customer needs to be aware that the door outer glass gets hot and the area where the glass vents behind the handle can get hotter yet. Caution needs to be taken. Showed customer what the manual indicates that this is normal. Please fill out survey.
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Grand Junction, Colorado 81504
James R
Job Details:
03/27/2026
Signed disclaimer. Removed lint screen air actually comes out of the area. This shows a restriction. Removed rear panel and checked at btm of the lint screen tube it is clear and blower is in good shape. When vent is removed from home air sucks down into lint screen area. So this indicates a bad restriction in the home. This needs to be taken care of before the dryer will dry as should. Please fill out tech satisfaction survey. Thank You.
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS3
Near Breckenridge, Colorado 80424
Antonio
Job Details:
03/27/2026
Installed new water valve then ran a cycle for proper operation and unit tested good Also advised cx of whlp survey
We serviced a
SPEED QUEEN DRYER ELECTRIC
Model DR5004WE
Near Ashland, Oregon 97520
Kyle
Job Details:
03/27/2026
"Found dryer cycling well, temps holding good. Customer states dryer vent was cleaned. Appeared to have new corrugated vent put on unit, vent is extremely long and bent over 360 degrees before entering the wall. Found vent runs about 15 feet turning another 180plus degrees to the outside vent. Advise customer that vent from unit to wall need to be shortened and have less bend in it."
We serviced a
WOLF RANGE
Model DF36650/S/P
Near Colorado Springs, Colorado 80904
Charles
Job Details:
03/27/2026
Replaced front right spark module
We serviced a
KITCHENAID ICE MACHINE
Model KUIX335HPS01
Near Los Ranchos de Albuquerque, New Mexico 87107
Larry
Job Details:
03/27/2026
"CX complaint - Ice machine has no power - Inspected unit and found the unit dead with a good 120ac at the wall - When I started pulling the machine out, it came back on - Inspected unit for pinched or damaged power cord and all is normal - CX had a large RO filtration systen installed under the sink so I could get to where the lines come through the cabinet - Unit is operating as design as of now - Advised Cx that if it goes out again I will need full access under the sink - Collected SC-auth-X9Y9ME"
We serviced a
GE WASHER
Model GFW655SPV0DS
Near Grand Junction, Colorado 81507
Sean
Job Details:
03/27/2026
"Verified the unit information customer signed disclaimer.Checked the unit and put it into service mode .Tested hot water valve it tested good.Tested the cold water valve it tested good. Started a quick wash with cold water .Unit filled with cold water.Drained and reset the unit Started a quick wash with warm water The unit filled with warmer water. Drained and reset the unit. Started the unit on a quick wash , hot water Unit filled with hot water. Called TAG. Tested the tub thermistor .It is reading accurate temperatures.They told me that the internal settings are Warm = 85?fHot = 105? fCase # ( 21516699 )The unit is operating as designed by factory.Thank you."
We serviced a
WHIRLPOOL WASHER
Model WFW5720RR0
Near Central Point, Oregon 97502
Kyle
Job Details:
03/27/2026
Found slight mold on siphons of softener and detergent. Customer had stated appliances were in a garage. Mold may have been from water pre existing in machine and moisture created mold. Advised customer how to clean with hot water. Wiped put detergent cup and tested. Unit is operating as intended.
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/27/2026
"Door hinge is pulling door upwards, removed and replaced, tested unit, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW5010LW0
Near Medford, Oregon 97504
Chris
Job Details:
03/27/2026
Replaced the drive belt and tested.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRMF3636RZ00
Near Grants Pass, Oregon 97526
Chris
Job Details:
03/27/2026
Replaced the water valve and reservoir and tested.
We serviced a
SAMSUNG WASHER
Model WA50R5200AW/US
Near Grants Pass, Oregon 97526
Chris
Job Details:
03/27/2026
Replaced the drain pump and tested
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
03/27/2026
Installed control board ran test and calibration runs all ok
We serviced a
WHIRLPOOL DRYER
Model WGD5720RR0
Near Central Point, Oregon 97502
Kyle
Job Details:
03/27/2026
"Found F3E3 error code, replaced both thermistors and thermostat. Vent to outside of house clear and blowing strong. Advised customer if problem persist, we will order main control."
We serviced a
SAMSUNG MICROWAVE
Model ME21DG6300SRAA
Near Colorado Springs, Colorado 80924
Brandon
Job Details:
03/27/2026
Replaced motor and tested operation all checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Sutherlin, Oregon 97479
Chris
Job Details:
03/27/2026
Replaced the fill valve and capacitor. Tested.
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS2
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
03/27/2026
Replaced broken upper rack left side adjuster.RKPart 67.90Tax 5.56MPS 14.50Labor 209.95S/C 149.95Total 447.86Auth 3AJHCV; used 1 WPW10546503 (ADJUSTER) from stock
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Rio Rancho, New Mexico 87124
Tye
Job Details:
03/27/2026
Arrived and removed failed motor assembly. Installed new motor assembly. Checked for leaks. No leaks from motor. The fill line has a very slow drip. Informed cx needs to have gill line replaced. Informed cx of review process.
We serviced a
PROFILE WASHER
Model PFW870SPV0RS
Near Breckenridge, Colorado 80424
Erik
Job Details:
03/27/2026
AFO RESPONSIBLE FOR FRONT PANEL REPLACEMENTMOUNT DAMAGE AND UNIT WAS SCRATCH AND DENT - CAN NOT WARRANTY COSMETICJOB COMPLETE
We serviced a
BEKO DISHWASHER
Model n/a
Near Colorado Springs, Colorado 80904
Ralph
Job Details:
03/27/2026
"found a loose screw that was interferring with the door closing , removed screw an unit checked okay, cust to monitor...autho no. 3wkrcw"
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/27/2026
"Door hinge is pulling door upwards, removed and replaced, tested unit, working well. Advised customer of situation and survey."
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Pueblo, Colorado 81006
James
Job Details:
03/27/2026
"Found 2 piece part of fill funnel separated causing very small leak. All clips looked good secured 2 pieces together, tested ops all ckok of problem persist will need valve W11797439 left litmus and talked survey"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ12
Near Clifton, Colorado 81520
James R
Job Details:
03/27/2026
Signed disclaimer. Replaced icemaker cycled wtr in is working as designed. Cleaned condenser was dirty. Please fill out tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW4855HW3
Near Fountain, Colorado 80817
Carlos
Job Details:
03/27/2026
Installed control board ran test and calibration runs all ok
We serviced a
LG WASHER
Model WM6998HBA.ABLEEUS
Near Colorado Springs, Colorado 80905
Mathew
Job Details:
03/27/2026
"Found complete restriction of drain behind pump. Remove clog, test op all okay. Collect svf 149.95 $149.95 CC Auth# V93XET"
We serviced a
KITCHENAID REFRIGERATOR
Model KRFF577KPS02
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
03/27/2026
Unit not making any unusual noises at this time. Tested all functions from user interface ok. Tightened loose door handle and instructed customer not to put product directly in front of air vent in fresh food section. RK
We serviced a
BOSCH REFRIGERATOR
Model B36CD52SNS/01
Near Colorado Springs, Colorado 80920
Ryan
Job Details:
03/27/2026
"Cleared jammed ice from icemaker and ran all functions successfully through diagnostic mode, including ice box fan, mold heater. Icemaker cycled and filled, allow 24 hours for ice production. RK"
We serviced a
MAYTAG WASHER
Model MFW7020RF0
Near Colorado Springs, Colorado 80924
Jason
Job Details:
03/27/2026
"7196598443Replaced all four dampeners and had issues with a couple of them being stuck, replace the bellow and tested the unit and diagnostic cycle and check for any leaks. Unit repaired"
We serviced a
BREDA DISHWASHER
Model LUDWT30155
Near Tigard, Oregon 97224
Austin
Job Details:
03/27/2026
3/27/26 BA: Installed new hardware to properly install the dishwasher and have it mounted to cabinets. Door open and closes without any issues and service complete.
We serviced a
WHIRLPOOL WASHER
Model NTW4519JW2
Near Parachute, Colorado 81635
Clint
Job Details:
03/27/2026
Customer signed disclaimer and recieved transmission previously ordered. Installed new transmission put it in service mode to reset the control. Ran unit with no leaks detected. Left leak detector under unit.
We serviced a
GE DISHWASHER
Model PDP755SYRBFS
Near Grand Junction, Colorado 81505
James R
Job Details:
03/27/2026
Signed disclaimer. Removed the door. the black insulation was stuck to the foam had a heck of a time getting it loose. Replaced vent fan assy. Then reassembled unit. Please fill out tech satisfaction survey. Thank You.
We serviced a
BOSCH DISHWASHER
Model SHE53C86N/01
Near Portland, Oregon 97214
Austin
Job Details:
03/27/2026
3/27/26 BA: Removed and replaced faulty soap dispenser and tested unit. Found no leaks after new part installation. Soap dispenser now opens during wash cycle.
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Colorado Springs, Colorado 80925
Earl
Job Details:
03/27/2026
Install the new solenoid and test.It unit is operating properly with no leaks at this time
We serviced a
MAYTAG WASHER
Model MAV7757AWQ
Near Pueblo, Colorado 81006
James
Job Details:
03/27/2026
Found unit needing full rebuild gc seals and bearings. Parts are nla called homeserve to report unit is being replaced. Advised cust
We serviced a
AMANA WASHER
Model NTW4519JW2
Near Pueblo, Colorado 81005
Domingo
Job Details:
03/27/2026
Replaced the control calibrated control ran diagnostic it passed no noise no extra vibrations
We serviced a
MAYTAG WASHER
Model MHW5630HC3
Near Colorado Springs, Colorado 80918
Ryan
Job Details:
03/27/2026
Machine working properly on all settings. Found user had spin option turned off on multiple settings which is why her clothes werent spinning out. Customer also had drain hose too far down into drain which could have been syphoning water back into unit. Made adjustments reset machine. RK
We serviced a
BOSCH MICROWAVE
Model HMB30155UC/001
Near Colorado Springs, Colorado 80917
Ryan
Job Details:
03/27/2026
Replaced damaged waveguide cover. RK
We serviced a
WHIRLPOOL DRYER
Model WED4107SW0
Near Bend, Oregon 97702
Levi
Job Details:
03/27/2026
"Found high limit thermostat tripped on heater, replace tested good; used 1 WP3977767 (Thermostat) from stock"
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/27/2026
"Door hinge is pulling door upwards, removed and replaced, tested unit, working well now. Advised customer of situation and survey."
We serviced a
PROFILE WASHER
Model PFW870SPV0RS
Near Colorado Springs, Colorado 80908
Earl
Job Details:
03/27/2026
Install the solenoid and tested it in diagnostic. Everything is coming on and running the way that it's supposed to
We serviced a
WHIRLPOOL RANGE
Model WFES3530RS0
Near Colorado Springs, Colorado 80921
Aaron
Job Details:
03/27/2026
"Door hinge is pulling door upwards, removed and replaced, tested unit, working well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4957PW0
Near Bend, Oregon 97701
Richard
Job Details:
03/27/2026
Installed new control re-calibrated unit cycle tested all checks good at this time
We serviced a
KITCHENAID REFRIGERATOR
Model KRFC300ESS12
Near Albuquerque, New Mexico 87122
Tye
Job Details:
03/27/2026
Arrived and cx complaint of not cooling at few days ago. They unplugged unit 3 days ago . Plugged back in yesterday. It is now cooling. Temps are good when I arrived. I tested compressor amps(.8 amps) condenser fan working. Cannot duplicate noise cooling issue. Informed cx to let us know what happens. 30 day warranty on svc call.
We serviced a
SAMSUNG RANGE
Model NE63A6511SS/AA
Near Colorado Springs, Colorado 80917
Mathew
Job Details:
03/27/2026
"Replace control and display. Test op, unit working as expected. All okay."
We serviced a
GE RANGE
Model C2Y366P2T1S1
Near Bend, Oregon 97707
Levi
Job Details:
03/27/2026
"Replaced spark module and electrodes, tested and all checks okay"
We serviced a
LG REFRIGERATOR
Model LRMDS3006D/01
Near Redmond, Oregon 97756
Richard
Job Details:
03/27/2026
Rebuilt sealed system recharged with R600 Freon unit cooling at this time
We serviced a
BLUESTAR RANGE
Model RGTPB484GCBSS
Near Peyton, Colorado 80831
Ryan
Job Details:
03/27/2026
Replaced switch for middle grill burner. Tested operation and grill now working properly. RK
We serviced a
AMANA RANGE
Model AEP222VAW
Near Leadville, Colorado 80461
Antonio
Job Details:
03/27/2026
"Installed new infinite switches, burner and knobs then tested each burner and unit is working properly"
We serviced a
VIKING REFRIGERATOR
Model VCBB363RSS
Near Colorado Springs, Colorado 80909
Ralph
Job Details:
03/27/2026
"unit haqs aq faulty inverter, would need new inverter, part 739.49, tx 60.64, mps 14.50, labor 269.95, total 1084.58. cust paying service fee 169.95...autho no. W4EFY3"
We serviced a
MAYTAG DISHWASHER
Model MDB8959SKZ0
Near Colorado Springs, Colorado 80915
Charles
Job Details:
03/27/2026
"Fill and drain only. Wash motor failure. Need sump assembly W11416363, Service fee $149.95, Labor $239.95, MPS $14.50, Part $317.67, Tax $26.05, Total $748.12, declined estimate paid service fee autho RPXVAL"
We serviced a
KENMORE REFRIGERATOR
Model n/a
Near Colorado Springs, Colorado 80924
Charles
Job Details:
03/27/2026
"6 flash error code on board, need compressor TCA38091801, drier ADH73150210, Service fee $149.95, Labor $695.95, Refrigerant $255.95, MPS $14.50, Parts $707.42 & $172.92, Tax $72.19, Total $2068.88, declined estimate paid service fee check #6176 autho P9AJ49"
We serviced a
SAMSUNG WASHER
Model WA45T3200AW
Near Colorado Springs, Colorado 80916
Earl
Job Details:
03/26/2026
"Customers complaint unit is not finishing the lid lock locks.It stays locked eventually it unlocks.I arrived and put it in a diagnostics.It gave me a 3C error code meaning clutch gear case area. I lifted the unit up got down underneath and tucked in all the way around the outside edge was closed and a whole bunch of pods, and there was a shirt caught in the clutch gear case, I was able to pull it out without damaging anything and I put it back. In the diagnostics that ran all the way through unit is operating properly at this time."
We serviced a
SAMSUNG REFRIGERATOR
Model RF27T5501SR/AA
Near Central Point, Oregon 97502
Chris
Job Details:
03/26/2026
"Replaced the compressor, drier filter and and step valve. Charged with 75 grams of R600A."
We serviced a
SAMSUNG REFRIGERATOR
Model RT70F18LASRAA
Near Central Point, Oregon 97502
Kyle
Job Details:
03/26/2026
"Found evaporator fan not running, replaced rear panel with fan assembly. Teated. Unit is set to recommended factory temps, unit operating as intended."
We serviced a
AMANA WASHER
Model A206
Near Colorado Springs, Colorado 80903
Earl
Job Details:
03/26/2026
"Customer's complaint unit, leaking water. It was a 4 digit model number may tag I have no idea the age of the unit but it is very old, I ran it and finally found on the left side of the unit. The hose runs into a plastic Junction piece where the hose attaches it's plastic, there's holes in it for vents, I guess and a small hose running through the middle and it runs the water into the hose on the other side and then into the washer, there was a small drip I removed the clamp and made sure there was no cracks or splits in the hose or the plastic, there was not I reattached it and moved it around a bit, and it stopped. Leaking unit is operating properly league free at this time. I told the customer we couldn't find parts for it and right now it's not leaking at all.Customer paid service fee authorization code3W3W9J"