We serviced a
SAMSUNG REFRIGERATOR
Model RF28HDEDBSR/AA
Near Colorado Springs, CO 80923
Brandon
Job Details: 02/05/2024
"Error 39 c replaced ice maker, auger and tray, tested op all checks ok hasd oqc passed"
We serviced a
SAMSUNG WASHER
Model WA55A7700AV/US
Near Colorado Springs, CO 80923
Brandon
Job Details: 02/05/2024
"Replaced harness, tested op all checks ok hass oqc passed"
We serviced a
SAMSUNG DRYER
Model DVE45B6300P/A3
Near Colorado Springs, CO 80908
Brandon
Job Details: 02/05/2024
"Error HC, replaced parts, tested op all checks ok hass oqc passed"
We serviced a
WHIRLPOOL DRYER
Model WED500CMW0
Near Colorado Springs, CO 80924
Aaron
Job Details: 02/05/2024
"Idler lodged, motor not securely mounted, replaced components and secured, tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL WASHER
Model CAE2745FQ1
Near Pueblo, CO 81004
Domingo
Job Details: 02/05/2024
"Install board, coin slider interface, temperature, main board , lid switch and drain pump test up"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJB00
Near Colorado Springs, CO 80903
Ralph
Job Details: 02/02/2024
"calledtech support due to cust experiencing temp flucuations, took temp readings from iside unit andohm readings off the p2 connector black wires for freezer and white wires for the ff section, the numbers i read off to the tech he stated thta the resistance on the evap thermister is out of range and that the thermister is not a serviceable part, andthat unit is non repairable. file #7738393459"
We serviced a
MAYTAG WASHER
Model MVWB855DC3
Near Colorado Springs, CO 80906
David
Job Details: 02/02/2024
"Checked washer, found slider not sliding, stuck. Ran diagnostics F7E5 code Replaced sliderCleared codes Ran diagnostics cycle, no codes after Ran cycle, running good"
We serviced a
GE DISHWASHER
Model GDF535PGR0CCI
Near Colorado Springs, CO 80904
Ralph
Job Details: 02/02/2024
"tub is warped a little but when installers installed the unit they left a large gap from the top of the unit where the door latch is, so the door would not latch correctly, cust and i found some shims and put the ontop of the unit and the door is closing much better and latching and unit is able to be to used..cust paid total autho no X3HMN3"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706EBS01
Near Colorado Springs, CO 80923
Glenn
Job Details: 02/02/2024
"Possible Frzr door was left open, frost buildup on FRZR Evap. test 6 >03 = Defrost Test for 20 minutes. Check Control > P8 > 8 PIN> PINS 1 &2, ORG /VIOLET0F = 22k ohm. SR# 7738393442 , Customer opted to do a manual defrost. He will call back if problem continues. Paid SC $129.95 via check #1081 , Autho# 4YJJV4"
We serviced a
ZLINE RANGE
Model RA-BR-36
Near Colorado Springs, CO 80907
Ralph
Job Details: 02/02/2024
"had to reset the hi limit, unit checked okay"
We serviced a
SUBZERO REFRIGERATOR
Model BI-42UFD1D/0
Near Colorado Springs, CO 80906
Ralph
Job Details: 02/02/2024
"water no tgetting to the ice mkr, replaced the valve andunit chekced okay, autho no. 34ex3c"
We serviced a
WHIRLPOOL WASHER
Model WFW9550WW00
Near Colorado Springs, CO 80904
Carlos
Job Details: 02/02/2024
"Ran test, needs control board, part is discontinued (W10251767) no repair. $129.95 CC Auth# L3Y9XH"
We serviced a
JENN-AIR COOKTOP
Model JIC4536XS
Near Colorado Springs, CO 80921
Glenn
Job Details: 02/02/2024
"cktp not heating properly/error code.Customer does not remember error codes. Center burner seems to have problems with whole pan/pot showing heat, seems only in center at times, then if they turn heat up and back down, appears to cook more uniformly. Also gets an overheat message w/ a specific thick cast iron pot. fan motors do appear to be running during operation. Explained that all Pots / Pans can function differently, suggest test using a diff. pot if problem occurs to see if specific to pot. Techline: Verified Unit Program to code 25, All OPS Test:OK, Unable to duplicate any errors. SR#7738392423"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Albuquerque, NM 87110
Jason
Job Details: 02/02/2024
installed parts unit checks ok
We serviced a
WHIRLPOOL RANGE
Model WGE745C0FS01
Near Peyton, CO 80831
Jerimiah
Job Details: 02/02/2024
"Installed replacement components. Calibrated both ovens to -30, unit seems acceptable, unit check ok."
We serviced a
INSINKERATOR GARBAGE DISPOSAL
Model 79355A-ISE
Near Colorado Springs, CO 80904
Ralph
Job Details: 02/02/2024
"replaced disposal and unit checked okay, Amy not sure if i was suppose to change the model and serial in the ticket but info on theticket is old unit"
We serviced a
WHIRLPOOL DRYER
Model WED7120HW2
Near Fort Carson, CO 80902
David
Job Details: 02/02/2024
Replaced heat air ductAll good
We serviced a
WOLF GAS COOKTOP
Model SRT364G
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 02/02/2024
"Back left and front left surface burners were not igniting/constantly clicking. Cleaned burner heads and igniters. Unit check ok back left still may have issues so notated the part number for future reference. Office working on charging card, unable to remotely charge.809706 BL Surface burner head"
We serviced a
GE RANGE
Model PGS950SEF5SS
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 02/02/2024
"Installed replacement bake igniter. Unit check ok, charged labor as quoted $189.95 $189.95 CC Auth# XY43TT"
We serviced a
MAYTAG DRYER
Model MEDB835DC4
Near Peyton, CO 80831
Aaron
Job Details: 02/02/2024
"Rollers and idler have worn from use, removed and replaced components, tested unit, working and heating well now. Advised customer of 5 star survey."
We serviced a
WOLF DOUBLE WALL OVEN
Model DO30PM/S/PH
Near Colorado Springs, CO 80924
Jerimiah
Job Details: 02/02/2024
Installed replacement relay board. Unit check ok.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Rio Rancho, NM 87144
Joe
Job Details: 02/02/2024
cx complaint - lid not latching - top load washer - lid not locked - cycle won't start - replaced parts ordered last visit and tested - unit good to go
We serviced a
GENERAL ELECTRIC REFRIGERATOR
Model ZIW303NPPBII
Near Silverthorne, CO 80498
Erik
Job Details: 02/02/2024
install door panel on siteJOB COMPLETE
We serviced a
WHIRLPOOL REFRIGERATOR
Model ED2GVEXVD01
Near Colorado Springs, CO 80907
Carlos
Job Details: 02/02/2024
Cx replaced their filter. Did not flush 3 gallons through system. Flushed system runs ok
We serviced a
WHIRLPOOL DRYER
Model WGD4815EW2
Near Colorado Springs, CO 80909
Carlos
Job Details: 02/02/2024
"Installed burner, checked for gas leaks. Found no leaks runs ok, heats up ok"
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Colorado Springs, CO 80919
Glenn
Job Details: 02/02/2024
Broken upper element support. Install New Support. All OPS Test: ok
We serviced a
GE DISHWASHER
Model PDT855SMJ2EF
Near Colorado Springs, CO 80906
Roman
Job Details: 02/02/2024
"Removed the old fill hose and installed new one, installed new drain hose and re routed it to help secure it. Ran the dw and checked for leaks. Dw working great. $289.95 CK Auth# XUWR9C"
We serviced a
SAMSUNG REFRIGERATOR
Model RF30BB6200QLAA
Near Peyton, CO 80831
Brandon
Job Details: 02/02/2024
"Replaced parts, vacuumed unit for 10 minutes, charged unit, compressor removing heat, cx will monitor, hass oqc passed"
We serviced a
SAMSUNG DRYER
Model n/a
Near Colorado Springs, CO 80908
Brandon
Job Details: 02/02/2024
"Found connector for thermostat not connected, secured and tested op all checks ok, Svf paid $129.95"
We serviced a
SAMSUNG REFRIGERATOR
Model RF18A5101SR/AA
Near Colorado Springs, CO 80918
Brandon
Job Details: 02/02/2024
"Replaced parts and tested op all checks ok compressor removing heat checked frost pattern and evap all ok, cx will monitor"
We serviced a
KITCHENAID DISHWASHER
Model KDFM404KPS0
Near Colorado Springs, CO 80927
Aaron
Job Details: 02/02/2024
"Circulation motor weak, not effectively pushing water, removed and replaced motor sump assembly, lifted front legs and tested unit, no leaks, installed litmus strip. Advised customer of 5 star survey. Auth 149.95 svf #44J3JT"
We serviced a
WHIRLPOOL DISHWASHER
Model WDF520PADM9
Near Colorado Springs, CO 80922
Aaron
Job Details: 02/02/2024
"Circulation motor is shorted out, removed and replaced motor sump assembly, tested and working well now, no leaks, installed litmus strip and advised customer of survey."
We serviced a
THERMADOR RANGE
Model PRD486WDGU/05
Near Silverthorne, CO 80498
Erik
Job Details: 02/02/2024
install board/test: GOODJOB COMPLETE
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9380SG/AA
Near Peyton, CO 80831
Mathew
Job Details: 02/02/2024
"Found icemaker iced up. Defrosted, sealed room and replaced all parts. Test op all okay."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHM08
Near Rio Rancho, NM 87144
Joe
Job Details: 02/02/2024
cx complaint - dripping from dispenser - side by side refrigerator - from dispenser housing - installed parts ordered last visit and tested - unit good to go
We serviced a
WHIRLPOOL DRYER
Model WGD5100HW3
Near Corrales, NM 87048
Joe
Job Details: 02/02/2024
cx complaint - dryer not drying properly-dryer cycles not completing - inspected unit - not heating - replaced thermal cut off - unit good to go; used 1 WP8573713 (fuse cut off) from stock
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB8600QLAA
Near Colorado Springs, CO 80921
Mathew
Job Details: 02/02/2024
Found leak from filter case. Replaced and test op all okay.
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HFEDBSR/AA
Near Colorado Springs, CO 80919
Mathew
Job Details: 02/02/2024
"Replaced all icemaker parts, room is sealed. Test op all okay."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS331SDHM06
Near Colorado Springs, CO 80922
Aaron
Job Details: 02/02/2024
"Scratches and dents on RC door, removed and replaced door, no scratches or dents, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ
Near Colorado Springs, CO 80925
Carlos
Job Details: 02/02/2024
"Called techline whirlpool and Assurant cx has a loading issue with food blocking air vent. SR 7738386528 checked thermostats all ok, temperature all ok adjusted FC temp from 0 to 1 degree and RC from 36 to 38 degrees air vent opens and closes. Cx will observe."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ04
Near Grand Junction, CO 81503
James R
Job Details: 02/02/2024
Signed disclaimer.Removed all shelves. Rear panel. Replaced control. Reassembled and test control working as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MVWB835DW1
Near Albuquerque, NM 87114
Joe
Job Details: 02/02/2024
cx complaint - when she has her washer on the normal it does not spin out - inspected unit - no errors - did calibration cycle - unit good to go
We serviced a
WHIRLPOOL FREEZER
Model WZF34X18DW07
Near Pueblo, CO 81006
Kris
Job Details: 02/02/2024
installed all parts sent ran test op all ok at this time cx will monitor unit before loading.
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, CO 80938
Aaron
Job Details: 02/02/2024
"Heating element and thermostat are shorted out, removed and replaced components, tested unit and heating well. Built up lint in vent hose with collected moisture, recommend wall duct to be professionally cleaned. Advised customer of 5 star survey."
We serviced a
GE DRYER
Model GFD14ESSN1WW
Near Breckenridge, CO 80424
Erik
Job Details: 02/02/2024
install/test: GOODJOB COMPLETE
We serviced a
MAYTAG WASHER
Model MVW5430MW0
Near Grand Junction, CO 81506
James R
Job Details: 02/02/2024
Signed disclaimers. Replaced suspension. Also TSP W11695259 noise and vibration. Adjusted rear panel. Did a service diagnostics did fine no issues. In spin unit is relatively smooth no issue empty if unit gets to shaking customer will need to reposition cloths. Also Use deep water wash or max fill for loads to make sure sufficient amount of water. Do not overload no more than 3/4 full. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL DRYER
Model WED8620HC2
Near Colorado Springs, CO 80910
Glenn
Job Details: 02/02/2024
"Reseat connections to PCB and heating circuit. , Unit is now heating and cycling heat. Slight restriction in vent, suggest have vent system checked out. All OPS Test:OK"
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SR/AA
Near Colorado Springs, CO 80908
Mathew
Job Details: 02/02/2024
Replaced scratched door. Test op all okay.
We serviced a
WHIRLPOOL DRYER
Model WED87HEDC1
Near Albuquerque, NM 87109
Jason
Job Details: 02/02/2024
checked unit found idler and rollers where worn instsalled repair kit from truck stock unit checks ok; used 1 4392067 (repair kit) from stock
We serviced a
GENERAL ELECTRIC RANGE
Model PHS930YP7FS
Near Frisco, CO 80443
Erik
Job Details: 02/02/2024
Product in sabbath mode - unlock control and test: GOODemail CX user manual for control use and care
We serviced a
GE WASHER-DRYER COM
Model GUD27ESSM1WW
Near Leadville, CO 80461
Erik
Job Details: 02/02/2024
stuck button asm - remove and remounttest: GOODJOB COMPLETE
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ04
Near Albuquerque, NM 87122
Jason
Job Details: 02/02/2024
checked unit found fan is getting noisey unit still cooling properly cx does not wanna replace fanAuth code:9JNE9V$151.85
We serviced a
KITCHENAID DISHWASHER
Model KUDE70FXSS5
Near Albuquerque, NM 87122
Jason
Job Details: 02/02/2024
instaslled link supports unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WTW6150PB0
Near Fruita, CO 81521
James R
Job Details: 02/02/2024
Signed disclaimer. Replaced lid. Test operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW4800BQ1
Near Albuquerque, NM 87121
Larry
Job Details: 02/02/2024
Installed drain pump and tested good - Unit is good to go
We serviced a
MAYTAG DRYER
Model MED7230HW3
Near Albuquerque, NM 87120
Larry
Job Details: 02/02/2024
Installed UI and tested good - Unit is good to go
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS22
Near Albuquerque, NM 87120
Larry
Job Details: 02/02/2024
Installed support and tested good - Unit is good to go
We serviced a
KITCHENAID RANGE
Model KSGG700ESS3
Near Albuquerque, NM 87120
Larry
Job Details: 02/02/2024
CX complaint - Front Left burner not lighting - Inspected unit and found the burner misaligned - Aligned burner and tested good - Unit is good to go.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT311FZDW02
Near Rio Rancho, NM 87124
Joe
Job Details: 02/02/2024
cx complaint - not making ice - replacced ice maker ordered last time - tested unit - unit good to go
We serviced a
GE RANGE
Model JGBS66REK6SS
Near Leadville, CO 80461
Erik
Job Details: 02/02/2024
"gas flue shutter wide open - close shutter on flue and test: GOODCX: 'smell is gone, it was super strong before adjustment'JOB COMPLETE"
We serviced a
MAYTAG WASHER
Model MVW4505MW1
Near Albuquerque, NM 87112
Jason
Job Details: 02/02/2024
installed ui control unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT112CZJZ00
Near Moriarty, NM 87035
Jason
Job Details: 02/02/2024
installed control unit checks ok
We serviced a
SAMSUNG REFRIGERATOR
Model RF28R7351S
Near Pueblo West, CO 81007
Domingo
Job Details: 02/02/2024
Defrost ice maker took old one out took auger out put rtv put new auger and ice maker out it test okay
We serviced a
SAMSUNG WASHER
Model WF53BB8700AVUS
Near Colorado Springs, CO 80904
Roman
Job Details: 02/02/2024
"Washer has water inside, manually unlocked the door. Ran the washer and door lock is not locking properly, door and latch okay. Recommend replacing the door lock. Replaced the door lock and tested the washer. Washer door lock locking and unlocking properly. Made sure the gasket was sealing properly. Washer working great."
We serviced a
SAMSUNG WASHER
Model WA45T3200AW/A4
Near Colorado Springs, CO 80909
Roman
Job Details: 02/02/2024
"Removed the pressure switch a and control board, installed new panel control panel, control board and pressure switch. Installed new harness and put the washer back together. Tested it and it is working. Washer filling agitating and draining great."
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Pueblo West, CO 81007
Domingo
Job Details: 02/02/2024
Run test it has few codes in it including no communication to interface board I test everything came up that the clutch was bad took it apart found out slider was broke replace clutch and slider test it up and it tested okay
We serviced a
WHIRLPOOL WASHER
Model WTW7120HC0
Near Peyton, CO 80831
Aaron
Job Details: 02/01/2024
"Cold water hose not fully secure, hose to water dispenser assembly seeping water, secured hose and clamped and tested unit, working well and no leaks, installed litmus strip. Advised customer of 5 star survey."
We serviced a
FULGOR MILANO RANGE
Model F6PIR365S1
Near Colorado Springs, CO 80907
Ralph
Job Details: 02/01/2024
"found a loose connection on the main board, pulled the connector and reseated and the unit came on we tested burners and the oven"
We serviced a
WHIRLPOOL DRYER
Model WGD5000DW3
Near Albuquerque, NM 87112
Jason
Job Details: 02/01/2024
installed motor and blower wheel unit checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ2
Near Albuquerque, NM 87122
Jason
Job Details: 02/01/2024
installed dispensor unit checks ok
We serviced a
GENERAL ELECTRIC DRYER
Model GTD58EBSV0WS
Near Colorado Springs, CO 80915
Roman
Job Details: 02/01/2024
"Removed all the old thermistors ad thermostats, ran dryer in diagnostics and it passed the tests and went up in temps. Thermostats and heater all reading okay. Dryer working great."
We serviced a
KITCHENAID RANGE
Model KSGG700ESS7
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 02/01/2024
"Installed replacement thermal sensor and controller. Unit check ok, calibrated to +5, may need to increase to +10 based on Cust response."
We serviced a
GE REFRIGERATOR/TOP
Model GSE23GYPFS
Near Colorado Springs, CO 80907
Ralph
Job Details: 02/01/2024
"the cond fan motor was making a noise, made n adjustment to the blade and the noise appears to have stopped, let cust to call us back if issue comes back"
We serviced a
KITCHENAID REFRIGERATOR
Model KBRP20ELSS01
Near Colorado Springs, CO 80918
Glenn
Job Details: 02/01/2024
"Stopped making ice. Temps good at 6F, Cycle test ice maker, had a few cubes. Cycle Test OK , Fill Test > PassPossible Icemaker on its way out. Suggest replace icemaker if problem continues. Ice Maker - 4396418 $328.48 , Tax $26.94 , MPS $14.50 , SC $129.95 , Labor $179.95 , Paid SC fee of $129.95 , Autho# 39EMJ9"
We serviced a
WHIRLPOOL WASHER
Model MVW6200KW0
Near Colorado Springs, CO 80920
Glenn
Job Details: 02/01/2024
"Install New Glass Lid, Swap door catch from old lid to new lid, belt. All OPS Test:OK, Did pull out about 8 more coins from basket"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ02
Near Colorado Springs, CO 80918
Glenn
Job Details: 02/01/2024
"Customer indicated water started leaking from fill tube on top of unit, so he turned water supply off. Customer already had fridge pulled out from wall upon arrival. Install New Fill tube & Dual Valve. All OPS Test:OK , Paid Labor Balance of $239.95 , Y34C39"
We serviced a
SUB ZERO REFRIGERATOR
Model BI-48SID/O
Near Colorado Springs, CO 80917
Jessie
Job Details: 02/01/2024
Replaced ui and control. Test op. Counted diagnostics. Monitored the unit and made sure it started cooling. All ops good.
We serviced a
SAMSUNG DRYER
Model DVE45T3200W/A3
Near Colorado Springs, CO 80922
Mathew
Job Details: 02/01/2024
"Found bad element, replaced assy test op unit has a clog error code. Found buildup of wet lint in the wall, indicating clogged vent somewhere in wall. Removed vent, unit passed OQC."
We serviced a
SAMSUNG DRYER
Model DVE47CG3500VA3
Near Colorado Springs, CO 80922
Mathew
Job Details: 02/01/2024
"Found banging noise inside dryer. Inspected all rollers, found issue with fan motor. Replaced fan motor test op all okay."
We serviced a
WHIRLPOOL STOVE
Model WGG555S0BS00
Near Colorado Springs, CO 80908
Jerimiah
Job Details: 02/01/2024
Installed replacement upper bake igniter. Unit check ok charged labor as quoted $189.95 CC Auth# Y3CX39
We serviced a
GE RANGE
Model JB655YKAFS
Near Pueblo, CO 81001
James
Job Details: 02/01/2024
"found main board not receiving information from temp probe correctly. temp probe resistance ckok needs main board WB27X45467 211.21+tax, overlay WB07X46127 63.78+tax, sc 129.95, labor 189.95, mps 14.50. total: $631.94 cust has lowes warranty and will call them to set up SO. WHEN WE GET TICKET, ADD PARTS TO LOWES SO collected 129.95 $129.95 CK Auth# 94MEET"
We serviced a
MAYTAG WASHER
Model MVW7230HW0
Near Colorado Springs, CO 80903
Roman
Job Details: 02/01/2024
"Called tech support and there is a service bulletin out for this washer on the issue. Error f2e2 A tech was previously out hear and replaced the ui board, control board and inlet valve. I replaced the control board as well and error code is still showing, ohmed out the connection on the wires from the ui to the control board and they all ohm out okay. Calle Mf assurant because were throwing parts into a dead horse. They are offering a buy out to the cx. Service Pointer-number #W11436350"
We serviced a
MIDEA FREEZER UPRIGHT
Model WHS-507FWEW1
Near Colorado Springs, CO 80921
Jessie
Job Details: 02/01/2024
Compressor running all fans ads running. Unit has a leak in the system low side. Evap#15831000001582. NlaTax $Sc $129.95Refrigerant $255$14.50Labor $595.95Total $No return on parts
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS20
Near Peyton, CO 80831
Aaron
Job Details: 02/01/2024
"Temperatures for baking are off by over 30 degrees, removed and replaced copernicus and oven sensor, tested unit and heating well, no oven calibration needed. Advised customer of 5 star survey."
We serviced a
SUB ZERO REFRIGERATOR
Model CL4850S/O
Near Monument, CO 80132
Jessie
Job Details: 02/01/2024
Unit ice bin slide was coming out. Found tabs need to be tighter. Test op. All ok
We serviced a
WHIRLPOOL OVEN
Model WOS31ES7JS01
Near Peyton, CO 80831
Aaron
Job Details: 02/01/2024
"Removed and replaced thermal fuse, tested unit, working and heating well now. Total due was previously paid."
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Colorado Springs, CO 80915
Carlos
Job Details: 02/01/2024
"Installed timer and knob ran test, runs ok"
We serviced a
WHIRLPOOL WASHER
Model WTW8500DC6
Near Colorado Springs, CO 80917
Glenn
Job Details: 02/01/2024
Install New Lid. All OPS Test:OK
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ0
Near Pueblo, CO 81003
David
Job Details: 02/01/2024
"Checked dishwasher It is the clean light that is on, and other lights are off, and the slight vibration might be coming from the vent fan.Tech line says this is normal SR# 7738384305"
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Colorado Springs, CO 80923
Glenn
Job Details: 02/01/2024
"Install New Basket assy. Test using quick wash cycle & selected 2 rinses. 2nd rinse is not working as it should. Only puts about 2 cups of water, then proceeds to 2nd spin cycle. Techline: Suggest New PCB may be the difference, and may be programmed not to run a long 2nd rinse? SR# 7738233971 , Techline: Unable to make any additional suggestions or recomendations. Unable to submit this issue to engineering?! Suggest customer contact customer service for further options."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ08
Near Pueblo West, CO 81007
David
Job Details: 02/01/2024
Replaced defrost heater assembly Tested and Unit is running l
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX988SIBM03
Near Woodland Park, CO 80863
Ralph
Job Details: 02/01/2024
"the user interface in the middle drawer, waw interffering with thedoor swtches, disconnected the drawer andcust is happy with that repair..cusrt paid totl bill autho no. 3JX9U9"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS315SDHZ08
Near Pueblo, CO 81005
David
Job Details: 02/01/2024
"Icemaker is working fine.Ice getting stuck in chute, possibly from using a to tall of glass This is her first time using an icemaker with a dispenser."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Calhan, CO 80808
Aaron
Job Details: 02/01/2024
"Removed and replaced control, ran unit through calibration and diagnostic cycles, working well now. Advised customer of 5 star survey."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS05
Near Colorado Springs, CO 80921
Glenn
Job Details: 02/01/2024
"Install New Icemaker & 2 control PCB's. However, If problem continues, order Main PCB WPW10675033 (Thought this is what I had ordered prior, but there are 3 controls installed, ordered other 2 prior.) IM Error Code Test > Pass , Cycle Test IM > Pass , Fill Test > Pass , Allow 48-72 hours for ice production."
We serviced a
MAYTAG WASHER
Model MVWB855DC3
Near Colorado Springs, CO 80921
Glenn
Job Details: 02/01/2024
"lid wont lock (Intermittently)F5E3 - Lid Lock Will Not Unlock , F5E2 - Lid Lock Will Not Lock Or Lid Lock Failure ,F5E1 - Lid Switch Fault , F2E1 - UI Stuck Button , Cleared error codes, not able to run diagnostics, as it doesn't proceed steps properly. Techline: Bad UI , Possibly bad lid lock on its way out. Lid Lock working at this time however. SR# 7738379009UI Console - W11112662 $336.55 , Tax $27.60 , MPS $14.50 , (Quote for: Lid Lock Assy - W10861642 $170.08 + Tax$?)SC $129.95 , Labor $169.95 , Declined Estimate for now. Paid SC Fee of $129.95 via check #4539 , Autho# E9FV44"
We serviced a
BOSCH WASHER
Model WFMC3301UCI
Near Colorado Springs, CO 80919
Kris
Job Details: 02/01/2024
cx is deciding on repairs. unit has bad valves 00422244 102.8200422245 79.6200244479
We serviced a
WHIRLPOOL DRYER
Model WED4850HW0
Near Monument, CO 80132
Glenn
Job Details: 02/01/2024
"Install New Harness, Bracket, Socket, Bulb. Unable to test unit, as wiring to 240VAC outlet is wired improperly. Suggest have Electrician correct outlet before plugging in any appliannce to source outlet. vacuumed as much glass shavings as I could from inside of drum, where exploded bulb had leaked inside. Customer had builder rep. come by before I left."
We serviced a
WHIRLPOOL RANGE
Model KSEG700ESS2
Near Glenwood Springs, CO 81601
James R
Job Details: 02/01/2024
Replaced bake element and convection fan motor/element assembly. Test operation Ok Working as should. Customer paid $149.95 labor auth code. R9E49CPlease fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WOLF RANGE
Model DF48650G/S/P
Near Colorado Springs, CO 80904
Jerimiah
Job Details: 02/01/2024
"Back left burner clogged, cleared, burner kept clicking trying to ignite, cleaned igniter, unit check ok charged service call $149.95 CC Auth# 33PK43"