We serviced a
SAMSUNG DISHWASHER
Model DW90F89T0UMTAA
Near Colorado Springs, Colorado 80918
Mathew
Job Details:
10/07/2026
"Samsung deemed unit installation failure. Document all leak points. No evidence of leak found inside of machine, found supply line loose and leaking upon my arrival. Unit has been left with the power off, uninstalled."
We serviced a
MAYTAG REFRIGERATOR
Model MSS25N4MKZ12
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
10/07/2026
"Vibration from the sealed system traveling and vibrating at condenser, corrected and monitored, working well now. Discussed situation with techline amd documented. Advised customer of situation and survey. Case number 25218158"
We serviced a
WHIRLPOOL DRYER
Model WED4720RW0
Near Socorro, New Mexico 87801
Larry
Job Details:
10/07/2026
Checked and found loose connection at control - Secured connection and tested good - Unit is good to go
We serviced a
KITCHENAID WALL OVEN
Model KOEC727SPS00
Near Colorado Springs, Colorado 80919
Charles
Job Details:
10/07/2026
"Magnetron tip burnt off again, waveguide damage. Uploaded photos and spoke to tech line, sent photos, unit not repairable. Case #25211764"
We serviced a
GE DISHWASHER
Model GDP670SGV3BB
Near Carbondale, Colorado 81623
Clint
Job Details:
10/07/2026
Customer signed disclaimer and recieved parts ordered. Pulled unit out from the wall and removed heating element nuts and indtalled new element . Pushed unit back in mounted it i stalled new spray arm ran unit no leaks detected . PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT318FZDB11
Near Albuquerque, New Mexico 87107
Jason
Job Details:
10/07/2026
Installed air duct unit operation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DRYER
Model WGD6720RR
Near Aspen, Colorado 81611
Clint
Job Details:
10/07/2026
Customer signed disclaimer and stated the unit wont start. Right away I coukd tell the door was loose i tightened the screws on the frame and door shut properly. PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
MAYTAG DRYER
Model MEDP586KW0
Near Albuquerque, New Mexico 87108
Jason
Job Details:
10/07/2026
Installed timer ran timed dry cycle unit operation checks ok. spoke to cx about review
We serviced a
JENN-AIR RANGE
Model JDS1750ML1
Near Glenwood Springs, Colorado 81601
Clint
Job Details:
10/07/2026
"Customer signed disclaimer, stated the unit wont get up to temp.put oven in diagnostic and it came up with an F2E1 error which is stuck key. The door switch had a piece of tape that had worked its way to the side and wasn't closing the light switch . Took it off a d unit works properly. PLEASE TAKE TECH SURVEY THANKS.CLINT"
We serviced a
MAYTAG WASHER
Model MHW3505FW0
Near Carbondale, Colorado 81623
James R
Job Details:
10/07/2026
Signed disclaimers. Replaced drain pump and then bellow. Finished assembling. Then put thru a service diagnostics test. Went thru fine. Put a leak board under unit and took pic.Please fill out tech satisfaction survey. Thank You.
We serviced a
JENN-AIR WALL OVEN
Model JMC2430LL01
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
10/07/2026
"Wire terminal to UI not fully engaged, verified power to the UI console, programmed and tested unit, working and heating well now, verified by customer, customer to monitor. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Aspen, Colorado 81611
James R
Job Details:
10/07/2026
"Signed disclaimers. had office send to customer.Customer did sign. Replaced control,latch and drain pump. Then did a calibration and a service diagnostics test all went thru fine. Put a leak board under unit and took. Pic.Please fill out tech satisfaction survey. Thank You."
We serviced a
BOSCH RANGE
Model HIF5050MU/01
Near Avon, Colorado 81620
Erik
Job Details:
10/07/2026
access with prop mgmtinstall display glassjob completecx not available for signature/ waiver
We serviced a
BOSCH REFRIGERATOR
Model B36CT80SNS/47
Near Minturn, Colorado 81645
Erik
Job Details:
10/07/2026
previous door (replacement) installed by SAinstall door * see quick picsjob complete
We serviced a
SAMSUNG REFRIGERATOR
Model RF27CG5B30SRAA
Near Colorado Springs, Colorado 80927
Brandon
Job Details:
10/07/2026
Replaced door and tested hass passed
We serviced a
GE RANGE
Model JD630ST3SS
Near Montrose, Colorado 81401
Sean
Job Details:
10/07/2026
verified information customer signed disclaimer.turned off the bracket and removed the control panel and removed the control assembly. I installed the new panel assembly and reinstalled the control..reassembled the unit. restored the power and tested.the unit is functioning as designed by factory.thank you.please fill out a technician survey.
We serviced a
MAYTAG WASHER-DRYER COM
Model LSE7806ACE
Near Glenwood Springs, Colorado 81601
James R
Job Details:
10/07/2026
Signed disclaimers. Removed washer front panel. Found that the dampner pads are worn out. Would need two techs. Gave estimate to repair. $769.64 If needs the part above the pads else lots of items are not availble. She will replace unit. Customer paid Service call $149.95 auth code. LN9VC3Please fill out tech satisfaction survey. Thank You.
We serviced a
SAMSUNG MICROWAVE
Model ME16A4021AS/AA
Near Peyton, Colorado 80831
Brandon
Job Details:
10/07/2026
replaced door and tested operation all checks ok
We serviced a
SPEED QUEEN WASHING MACHINE
Model AWN43RSN116TW01
Near Peyton, Colorado 80831
Brandon
Job Details:
10/07/2026
Replaced water valve and tested ran cycle all checks ok
We serviced a
FRIGIDAIRE REFRIGERATOR
Model PRFS2883AFF
Near Colorado Springs, Colorado 80919
Brandon
Job Details:
10/07/2026
"Ice maker was turned off, turned on and checked temps freezer at 0 and fridge at 34 all checks ok no issues"
We serviced a
SAMSUNG REFRIGERATOR
Model RF29A9671SR
Near Colorado Springs, Colorado 80919
Brandon
Job Details:
10/07/2026
Replaced ice pipe heaters cycled ice makers cx has water off to unit
We serviced a
BOSCH RANGE
Model HGI8056UC/01
Near Colorado Springs, Colorado 80908
Earl
Job Details:
10/07/2026
I install the new hot service igniter and tested it units operating properly at this time
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Colorado Springs, Colorado 80916
Carlos
Job Details:
10/07/2026
Installed ice maker all ok
We serviced a
MIELE REFRIGERATOR
Model KFNF9959
Near Vail, Colorado 81657
Erik
Job Details:
10/07/2026
ACCESS WITH PROP MGMTINDEX 20A191REF#1011865803CALL MIELE TAG:RUN ICE MAKER TEST Lr r2 ON SERVICE MODE - HARVEST: GOODREFILL: GOODICE MAKER WORKING!JOB COMPLETECX NOT AVAILABLE FOR SIGNATURE/ WAIVER
We serviced a
SAMSUNG WASHER
Model WA52DG5500AVUS
Near Selma, Oregon 97538
Chris
Job Details:
10/07/2026
Replaced the water valves and tested. Ran HASS and passed OQC submitted OQC.
We serviced a
KITCHENAID REFRIGERATOR
Model KRSF536RPS00
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
10/07/2026
"Auger motor broke coupler at ice bin assembly, motor is still working well, removed and replaced ice bin and coupler components, tested unit, working well now, verified by customer. Advised customer of situation and survey."
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS06
Near Colorado Springs, Colorado 80924
Aaron
Job Details:
10/07/2026
"Tightened FC door handle, corrected and verified unit to be level, discussed situation with techline, left RC deli drawer will close different than the right with the harness for the deli UI, glides use ball bearings to assist in close, this drawer does not use an auto close feature, sent pictures of drawer and glides, unit is working as designed. Advised customer of situation and survey. Case number 25217493"
We serviced a
GE RANGE
Model JBS360RM1SS
Near Colorado Springs, Colorado 80904
Briton
Job Details:
10/07/2026
"F2 ERROR CODE PARTIAL CONNECTION AT SENSOR RE-SECURED TESTED 1700 OHMS AT 400, BOARD CYCLING POWER TO BAKE CORRECTLY AUTH CODE MYV3L4"
We serviced a
SUB ZERO REFRIGERATOR
Model 642/F
Near Cave Junction, Oregon 97523
Chris
Job Details:
10/07/2026
I called TS to check the evaporator fan motor and the defrost heater. Both are working. The condenser fan is weak and needed help to spin. Once it started it ran fine. I suggested to the customer it should be replaced. He said that he will have one of his guys replace it. TS said the freezer my have been slightly left open to cause the evaporator to freeze up.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS970CIHZ00
Near Colorado Springs, Colorado 80905
Ralph
Job Details:
10/07/2026
"UNIT HAS A REFRIGERANT LEAK WILL NEED LISTED PART WPW10643261 ff evap 288.98, wp2188822 fz evap 308.91, going to install a dye filter drier to check unit for a leak ....cust needs to discuss the repair. WPW10143759 dye filter drier 74.00, tax 6.07, refrigerant 255.00, labor 895.95, total 1231.02cust paying service fee today of 149.95, if cust cintinues with the repair, i will need to install the dye drier to locate the location of the dye, and will need two hours for this repair autho no. 49VVVT"
We serviced a
ELECTROLUX DRYER
Model ELFE7738AW0
Near Monument, Colorado 80132
Earl
Job Details:
10/07/2026
Customers complaint unit was moved and started making a loud rumbling sound. I arrived and pulled the unit apart. Couldn't anything wrong? I put it back together now. The unit is no longer making any noise.
We serviced a
MAYTAG WASHER
Model MHW8200FC0
Near Colorado Springs, Colorado 80921
Earl
Job Details:
10/07/2026
"Customers complaint unit not draining the clothes at the end of the cycle and giving her error codes. The error codes are at a balanced suds and draining. I arrived and found the unit running through the diagnostic cycle. Perfectly fine, I discussed her loading of the washer and found she was not putting enough clothes in unit is operating properly at this time. Authorization code3K39EU"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT518SZFM05
Near Colorado Springs, Colorado 80920
Earl
Job Details:
10/07/2026
"Customer had the gasket for the freezer door gasket, it was not the gasket issue.When you closed the refrigerator door the freezer opens and then doesn't reclose.There is no apparatus closing the door if you lean the refrigerator back a little bit, it does help.\nLet alone the gask"
We serviced a
AMANA DRYER
Model NED4655EW1
Near Colorado Springs, Colorado 80923
Earl
Job Details:
10/07/2026
I installed heating element in thermostats unit is operating properly at this time.
We serviced a
SAMSUNG DISHWASHER
Model DW80CG5451SRAA
Near Lafayette, Oregon 97127
Blake
Job Details:
10/07/2026
"KB 10/7Ran unit and it fully drains, fills, agitates and drains again without noise. Noted garbage disposal is overflowing in sink. Likely debri is flowing back into pump. Advise running hot water and disposal before wash and using a soap with an enzyme. All good, no parts required at this time."
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Cedaredge, Colorado 81413
Sean
Job Details:
10/07/2026
verified information customer signed disclaimer.visually checked the unit and removed the lid assy.installed the new lid assy. removed the lid latch and installed it on the new lid .tested the unit the door registers open and closed.tested the unit good.thank you.
We serviced a
WOLF RANGE
Model DF366
Near Colorado Springs, Colorado 80906
Ralph
Job Details:
10/07/2026
"INSTALLED PART AND UNIT CHECKED OKAY..COLLECTED REMAINDER BALANCE OF 82.79, AUTHO NO. V9JRP3"
We serviced a
KITCHENAID DISHWASHER
Model KDTS324SPS0
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
10/07/2026
Installed listed parts runs all ok
We serviced a
MAYTAG DRYER
Model MEDC465HW0
Near Colorado Springs, Colorado 80906
Carlos
Job Details:
10/07/2026
Removed debris from blower wheel runs all ok cx paid DC $149.95 CC Auth# T3PECA
We serviced a
WHIRLPOOL DRYER
Model WED4720RW0
Near Lincoln City, Oregon 97367
Nathan
Job Details:
10/07/2026
Stacked unit Replaced console due to unit not starting See notes Tested Advised of survey
We serviced a
WHIRLPOOL RANGE
Model WFE500M4HS
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
10/07/2026
"Light switch is not making contact, removed and replaced switch and bulb, tested unit, working well now. Advised customer of situation and survey."
We serviced a
KENMORE REFRIGERATOR
Model 795.68279.900
Near Colorado Springs, Colorado 80918
Carlos
Job Details:
10/07/2026
Needs a compressor cx will not repair
We serviced a
WHIRLPOOL WASHER
Model WTW8127LC1
Near Colorado Springs, Colorado 80927
Earl
Job Details:
10/07/2026
"Customers complaint unit making a thumping noise. I arrived and ran the unit through a calibration cycle, a diagnostic cycle. I checked for codes. There were no codes. The calibration cycle went through fine. The diagnostic cycle went through fine. Tried to sever more times I couldn't find an issue with the unit units operating properly at this time."
We serviced a
ASKO DISHWASHER
Model DB1664THXXLD.U
Near Happy Valley, Oregon 97086
Austin
Job Details:
10/07/2026
10/7/26 BA: Cc unit turns on but wont start. Tech inspected the unit and found the door not closing properly and the display is blank. Tech took apart the display and found a loose connection at the ribbon cable. Turned unit back on and the display returned to normal. Leveled the unit to ensure proper door closing and started a quick cycle. No leaks or any other issues detected and service is complete.$309.40 CK Auth# 9XPJ34
We serviced a
THERMADOR RANGE
Model PRD486WDHU/14
Near Sisters, Oregon 97759
Levi
Job Details:
10/07/2026
"Used airsled to pull range out of pocket. Replaced board, thermostat and bake ele for small oven, tested and all checks okay"
We serviced a
SAMSUNG REFRIGERATOR
Model RF32CG5400SRAA
Near Woodburn, Oregon 97071
Blake
Job Details:
10/07/2026
KB 10/7Customer replaced water filter yesterday and ice is now being made for both the cubed and small ice. verified water flow is good and explained what to expect and how to reset timer. all good no need for parts at this time.
We serviced a
FRIGIDAIRE REFRIGERATOR
Model PRFG2383AFH
Near Culver, Oregon 97734
Levi
Job Details:
10/07/2026
Upon arrival I found that there was a little bit of water on the floor on the left hand side of the unit. Did not notice any damage to the wood floor. When I open the freezer up the entire bottom of it was iced over and so was the bottom of the refrigerator compartment. Also found that the ice maker was cracked due to freezing. I replaced the user interface and the man control board and the thermistors that RS had ordered. Cleared all the ice from the refrigerator section and from the freezer section and dried everything up the best I could. Homeowner is not here because this is a vacation home so I left the ice maker off just in case there's a problem and no one is here to address it. I did install the new filter that the customer had sitting on the counter. All tests are okay through diagnostics and the unit appears to be cooling as designed.
We serviced a
KITCHENAID DISHWASHER
Model KDTS424SPS0
Near Rifle, Colorado 81650
James R
Job Details:
10/07/2026
Was sent to the address there is no home just and shed. Tried to find part not there. Rick has further information.
We serviced a
WHIRLPOOL RANGE
Model WFE500M4HS
Near Colorado Springs, Colorado 80927
Aaron
Job Details:
10/07/2026
"Breaker is tripping when using bake cycle, rid of moisture in elements with burn off, working and heating well now. Advised customer of situation and survey."
We serviced a
WHIRLPOOL WASHER
Model WFW6620HC0
Near Colorado Springs, Colorado 80921
Torrey
Job Details:
10/06/2026
Temoved and replaced control board and control panel. Tested good.
We serviced a
WHIRLPOOL DRYER
Model WED8127LC2
Near Colorado Springs, Colorado 80923
Torrey
Job Details:
10/06/2026
Removed and replaced fuse kit and heater. Dryer heats now. All good.
We serviced a
WHIRLPOOL DISHWASHER
Model WDT730HAMZ1
Near Colorado Springs, Colorado 80918
Torrey
Job Details:
10/06/2026
Removed and replaced conteol board. Ran a service cycle. Tested good.
We serviced a
FRIGIDAIRE MICROWAVE
Model FMOS1746BSB
Near Colorado Springs, Colorado 80923
Earl
Job Details:
10/06/2026
I installed the door customers.Happy unit operating properly at this time
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ4
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
10/06/2026
"Loose connection, fixed runs all ok"
We serviced a
WHIRLPOOL DRYER
Model WED5100HW3
Near Colorado Springs, Colorado 80925
Carlos
Job Details:
10/06/2026
Restored loose connection runs all ok
We serviced a
SUBZERO REFRIGERATOR
Model IT-36CI
Near Colorado Springs, Colorado 80906
Mathew
Job Details:
10/06/2026
Found fridge drain line clogged. Unclog drain line. Test op. All okay. Collect Svf $169.95Labor $189.95Total collected $359.90
We serviced a
KITCHENAID VENT HOOD
Model KVUB606DSS6
Near Monument, Colorado 80132
Aaron
Job Details:
10/06/2026
"Vent hood is processing each level accordingly, vibration throughout the body of the unit, unit is properly mounted, discussed situation with techline, unit deemed working as designed, no further recommendations. Advised customer of situation and survey. Case number 25192260"
We serviced a
SAMSUNG RANGE
Model NX60A6511SS/AA
Near Colorado Springs, Colorado 80907
Brandon
Job Details:
10/06/2026
"Bad connection at bake ignitor, ignitor only pulling 2.8amps should be 3.4amps recommend replacing ignitor, svf paid $149.95 CC Auth# ECWMVX, brandon@d3appliance.com - QUOTE 10/6/2026LABOR: Range / Induction / Downdraft broil ignitor (Samsung ? LOW end ? Tier 2) $229.95PART: Part (shipping incl.) $296.08SERVICE CALL $149.95MPS $18.50SALES TAX (CO Springs rate ? parts only ? 8.2%) $24.28TOTAL $718.76"
We serviced a
LG DRYER
Model DLEY1701V
Near Colorado Springs, Colorado 80904
Brandon
Job Details:
10/06/2026
"Heater is working, cleaned moisture sensor, recommend vent cleaning"
We serviced a
SAMSUNG DRYER
Model DVE45T3200W/A3
Near Colorado Springs, Colorado 80906
Brandon
Job Details:
10/06/2026
"Cx concerned about noise, checked unit and indetified clogged venting recommend vent cleaning all other checks ok hass passed"
We serviced a
SUBZERO REFRIGERATOR
Model BI-42SD/O
Near Colorado Springs, Colorado 80919
Ralph
Job Details:
10/06/2026
"REPLACED LISTED PARTS AND UNIT CHECKEDE OKAY, CUST TO MONITOR"
We serviced a
WHIRLPOOL WASHER
Model WTW6157PB1
Near Rio Rancho, New Mexico 87144
Larry
Job Details:
10/06/2026
Installed parts lsited and tested good - Unit is good to go - Survey mentioned
We serviced a
MONOGRAM REFRIGERATOR
Model ZISS360DNMSS
Near Grand Lake, Colorado 80447
Erik
Job Details:
10/06/2026
WATER LINE FROM ISO VALVE DISCONNECTED - REATTACH/ TEST: PASS* SEE QUICK PICS FOR BEST VIEW (LEFT SIDE OF VALVE WATER LINE DISCONNECT)JOB COMPLETE
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Tillamook, Oregon 97141
Nathan
Job Details:
10/06/2026
Thermal fuse failureFuse was open- replacedTestedAdvised of surveySee notes
We serviced a
SAMSUNG DISHWASHER
Model DW80CG5451SR
Near Colorado Springs, Colorado 80915
Mathew
Job Details:
10/06/2026
Dishwasher is working as expected. All okay.
We serviced a
SAMSUNG REFRIGERATOR
Model RS27T5200SG/AA
Near Colorado Springs, Colorado 80911
Mathew
Job Details:
10/06/2026
Left compressor with customer. Did not install.
We serviced a
FRIGIDAIRE RANGE
Model FCRG3062AS
Near North Plains, Oregon 97133
Austin
Job Details:
10/06/2026
10/6/26 BA: installed new oven burner tube per recall procedure. Oven is operating after part replacement. Service complete.
We serviced a
SAMSUNG RANGE
Model NX58T5601SS
Near Fountain, Colorado 80817
Mathew
Job Details:
10/06/2026
Replace control and igniter. Test op all okay.
We serviced a
SUB ZERO REFRIGERATOR
Model BI - 48SD/S/PH
Near Portland, Oregon 97229
Austin
Job Details:
10/06/2026
10/6/26 BA: installed new dispenser parts and tested unit. Found no further issues and no leaks coming from the dispenser. Service complete.
We serviced a
GENERAL ELECTRIC WASHER
Model GTW485ASW0WB
Near Pueblo, Colorado 81005
David
Job Details:
10/06/2026
"Installed ordered parts, tested and is operating as designed."
We serviced a
MAYTAG DRYER
Model MEDX655DW1
Near Santa Fe, New Mexico 87505
Jason
Job Details:
10/06/2026
Installed timer and knob ran timed dry cycle to test operation. unit operation checks ok. spoke to cx about review
We serviced a
AMANA DISHWASHER
Model ADFS2524RZ0
Near Aspen, Colorado 81611
James R
Job Details:
10/06/2026
Signed disclaimers. Unit has not been mounted installed. I did not install. Removed door outer panel found control loose and out of position. One of the clips broken on the control. Installed control so mounted properly. Elec wiring to unit had been installed already as well as wtr line and drain hose. Re-installed outer panel and ran thru a service diagnostics. No errors when done. No leaks evident. Put a leak board under unit and took pic. Please fill out tech satisfaction survey. Thank You.
We serviced a
MAYTAG DRYER
Model MED5500FW0
Near Santa Fe, New Mexico 87507
Jason
Job Details:
10/06/2026
Installed parts listed ran timed dry cycle unit operation checks ok. spoke tto cx about review
We serviced a
WHIRLPOOL RANGE
Model WFG320M0MS0
Near Santa Fe, New Mexico 87507
Jason
Job Details:
10/06/2026
Installed control heat cycled unit. unitoperation checks ok. spoke to cx about review
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Colorado Springs, Colorado 80917
Torrey
Job Details:
10/06/2026
Control board sometimes clicks and starts nothing. Replaced control board and same issue. 12 ohms on wash motor. Tried removing one part at control board at a time. Same issue. Called tech support.Case number 25202133Turns out after tech hung up that it wasn't the float valve as suspected. Power was grounded out. Unplugged the cord and no grounding. Next plugge into a different outlet/circuit. Dishwasher runs normal.
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Albuquerque, New Mexico 87120
Larry
Job Details:
10/06/2026
Installed parts lsited and tested good - Unit is good to go
We serviced a
MAYTAG DRYER
Model MED4500MW0
Near Albuquerque, New Mexico 87105
Larry
Job Details:
10/06/2026
CX complaint - Dryer making thumping noise - Inspected unit and found the plastic strip aroung the drum loose - Secured bushing and tested good - Unit is good to go
We serviced a
MIELE COFFEE MACHINE
Model CM6160
Near Basalt, Colorado 81621
Clint
Job Details:
10/06/2026
Customer signed disclaimer and tech installed new switch ran unit through rinse cycle and it worked properly with no code. Advanced to select drink cycle with no problems.PLEASE TAKE TECH SURVEY THANKS.CLINT
We serviced a
LG REFRIGERATOR
Model LRFVS3006D/02
Near Pueblo West, Colorado 81007
James
Job Details:
10/06/2026
"Installed ordered parts. Pressurized with nitrogen to 200psi. Held pressure, vac down and held vacuum. Charged unit. Unit now moving heat. Advised cust to put bottle of water in freezer and monitor for 24 hrs."
We serviced a
WHIRLPOOL DRYER
Model WED4105SW1
Near Eagle, Colorado 81631
Antonio
Job Details:
10/06/2026
Found unit not level and dryer lid not sitting properly. Removed lid and readjusted also leveled unit .unit is level and looking good
We serviced a
SPEED QUEEN WASHER
Model AWN632SP116TW02
Near Colorado Springs, Colorado 80908
Earl
Job Details:
10/06/2026
"I installed the new belt idler, and\n Drain, cause it broke. It was coming off and tested. It unit is operating properly at this time."
We serviced a
GENERAL ELECTRIC WASHER
Model GFW550SSN4WW
Near Pueblo, Colorado 81001
James
Job Details:
10/06/2026
Installed ordered parts tested ops all ckok
We serviced a
WHIRLPOOL M/W OTR
Model WMMS3130RZ03
Near Eagle, Colorado 81631
Antonio
Job Details:
10/06/2026
"Found unit fan pointing wrong direction, flipped fan and now it goes up in the right direction"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRTX7421TZ00
Near Eagle, Colorado 81631
Antonio
Job Details:
10/06/2026
Found evap fan not working so i recommend and unit is working properly
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ00
Near Fountain, Colorado 80817
Carlos
Job Details:
10/06/2026
CX blocking air with products need to let air circulate properly CX paid SC $149.95 CC Auth# 4XKTR3
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Colorado Springs, Colorado 80911
Carlos
Job Details:
10/06/2026
"Ran cycle with full balanced load, unit runs as designed, cx needs to run balanced loads"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHW11
Near Central Point, Oregon 97502
Kyle
Job Details:
10/06/2026
Customer states unit is loud when running. Found ice maker chute out if place causing excessive noise in freezer section. Adjusted chute and unit is no longer making noise. Unit is operating as intended.
We serviced a
GE WASHER
Model GTW335ASN2WW
Near Pueblo West, Colorado 81007
David
Job Details:
10/06/2026
"Checked washer, and repaired lock"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2623ABC
Near Pueblo West, Colorado 81007
David
Job Details:
10/06/2026
"Replaced water valve, wrong fan motor, old one is ok. Water coming down from fill tube, removed ice from fan area. Running quieter."
We serviced a
KITCHENAID DISHWASHER
Model KDTE304RBS0
Near Colorado Springs, Colorado 80908
Aaron
Job Details:
10/06/2026
"Removed unit to replace components, noticed copper water inlet line kinked from installation, removed and replaced valve and motor sump assembly, reinstalled and tested unit through diagnostics, code is still intermittently occurring. Discussed situation with techline and documented, recommend plumber. Advised customer of situation and survey. Case number 25199191"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHV01
Near Central Point, Oregon 97502
Kyle
Job Details:
10/06/2026
"Replaced ice maker assembly, test cycled unit. Unit has water in tray. Advised customer to give 24 hours until they start taking from the ice bucket. Unit operates as intended."
We serviced a
SAMSUNG REFRIGERATOR
Model RF29BB8600QLAA
Near White City, Oregon 97503
Kyle
Job Details:
10/06/2026
"Customer states unit has low ice rates. Found ice maker heater connection not fully seated in unit, causing ice to not produce. Reconnected connector and test cycled unit. Unit is operating as intended. Ran HASS overall check, unit passed. Submitted report"
We serviced a
MAYTAG DRYER
Model MED5630HW2
Near Peyton, Colorado 80831
Aaron
Job Details:
10/06/2026
"Heating element and thermostat are shorted out, removed and replaced, tested unit, working and heating well now. Advised customer of situation and survey."
We serviced a
GE DISHWASHER
Model GSD3360K6555SS
Near McMinnville, Oregon 97128
Brandon
Job Details:
10/06/2026
Call tech-support. Tested heating element and drain. Both were working properly. No issues found. Tech-support said close out ticket.
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US
Near Peyton, Colorado 80831
Mathew
Job Details:
10/06/2026
"Unit is in a garage uninstalled. No water hookup. Cx states motor issue, leaking. Cannot test dw."
We serviced a
MAYTAG WASHER
Model MTW4205SW0
Near Santa Fe, New Mexico 87508
Jason
Job Details:
10/06/2026
"Checked unit found actuator failed damaging cam. installed cam and actuator. unit operation checks ok. spoke to cx about review; used 1 W11481722 (actuator), and 1 W10721967 (cam) from stock"
We serviced a
FRIGIDAIRE REFRIGERATOR
Model FRSS2623AS
Near Forest Grove, Oregon 97116
Blake
Job Details:
10/06/2026
"KB 10/6Monitored temps to confirm average temp of FF compartment 37 FR 1-2 and airflow directly in front of vent in FF is 23. Verified water lines are sealed at the back of the unit, that the vent does fully open and close, and that there is no ice build up in the fridge or freezer. No parts required at this time. Please ensure sensitive items like liquids especially in cans, and fresh produce are not in direct line of the top shelf in front of the vent. If items are freezing below please move to the front towards the door or put in a crisper drawer. If issue continues a photo of issue where it is placed would be helpful when letting us know."
We serviced a
MAYTAG DRYER
Model MED7230HW
Near Colorado Springs, Colorado 80923
Briton
Job Details:
10/06/2026
Install; harness and new sensors
We serviced a
KITCHENAID RANGE
Model KSES430SPS0
Near Colorado Springs, Colorado 80911
Briton
Job Details:
10/06/2026
INSTALLED NEW UI
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX986SIHZ00
Near Glenwood Springs, Colorado 81601
James R
Job Details:
10/06/2026
"Signed disclaimers. Checked pwr 121 vac good at pwr and control boards. But unit still wont pwr on. Checked all wire harneses at control,UI Deli drawer. Above door. Interior light dont work. Finally unplugged LED light board and the unit pwred up. Compressor and all functions came on. Unit is cooling. Customer at this point will not replace the lights or the LED control. Customer paid service call $149.95 auth code Y9L33LPlease fill out tech satisfaction survey. Thank You."

