Service History 25 - D3 Appliance

We serviced a

GE REFRIGERATOR/TOP

Model GNE25JYKHFFS

Near Pueblo, CO 81005

Domingo

Job Details: 02/27/2024

Install ice maker and water valve test it okay

We serviced a

SUB ZERO REFRIGERATOR

Model BI-42UFD/S/PH

Near Monument, CO 80132

Jessie

Job Details: 02/27/2024

Unit still in garage. Replaced top and grill. All ok

We serviced a

MAYTAG WASHER

Model MVWB765FW3

Near Colorado Springs, CO 80906

Roman

Job Details: 02/27/2024

"Ran the washer and it will agitate, drain and spin. Washer will not fill with water, checked the voltage and its good, also checked the screens on the inlet valve. Bad inlet valve. Recommend replacing it. Return later in the day and installed new valve. Checked for leaks and made sure hot and cold are working. Washer working great. Inlet valve #W11165546 $ $77.05Tax $6.32Parts total $83.37MPs $14.50Labor 159.95Sc $129.95Total cost $387.77"

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHW08

Near Colorado Springs, CO 80911

Ralph

Job Details: 02/27/2024

replaced heater harness and cust to monitor the unit

We serviced a

FRIGIDAIRE MICROWAVE

Model n/a

Near Colorado Springs, CO 80925

Ralph

Job Details: 02/27/2024

"too costly to repair, cust to replace,,,,cust paid total autho no. 9ME3LT"

We serviced a

VIKING RANGE

Model VDR5304BCB01

Near Colorado Springs, CO 80921

Jerimiah

Job Details: 02/27/2024

"Bullnose knob lighting not working. Techline says 12v toggle power supply red black 12VDC or blk wht 120VAC. When the bullnose was removed the lights activated. Unknown where problem lies but could not get unit to fail again, more than likely somewhere in wiring, good known part numbers listed. Charging service call. $172.44 CC Auth# E43EH3Power supply 069993-000Toggle 046283-000"

We serviced a

FRIGIDAIRE DISHWASHER

Model FGIP2468UF0A

Near Colorado Springs, CO 80925

Ralph

Job Details: 02/27/2024

"tub is warped and causing unit to leak, tub is discontinued, autho no. 99CPKL"

We serviced a

ASKO DISHWASHER

Model D5654

Near Colorado Springs, CO 80906

Ralph

Job Details: 02/27/2024

"wash pump is leaking, saw a couple drops of water coming off of it. part 700244 $539.00, tax $44.20, labor 259.95, other 14.50, sc 149.95, total cost 1007.60, cust paying service fee which will leave a remainder balance of 857.65...autho no. for SC, NRR43E"

We serviced a

SAMSUNG WASHER

Model WA50R5200AW/US

Near Colorado Springs, CO 80925

Mathew

Job Details: 02/27/2024

"Replaced clutch assy. Test op, all okay."

We serviced a

KITCHENAID DISHWASHER

Model KDTE204KPS2

Near Colorado Springs, CO 80909

Carlos

Job Details: 02/27/2024

"Installed sump assembly and control board, runs all ok, left leak strip."

We serviced a

WHIRLPOOL DRYER

Model WED495HW0

Near Peyton, CO 80831

Aaron

Job Details: 02/27/2024

"Heating element is shorted out, thermostats check out okay, Needs element. Approved onsite. Removed and replaced element. Tested and heating well now. Element 279838 $99.28Tax $8.14Supplies $14.50Hc $129.95Labor $179.95Total job $431.82No return on parts Auth total due $431.82 #94FW3U"

We serviced a

MAYTAG DRYER ELECTRIC

Model MED8200FC1

Near Colorado Springs, CO 80908

Aaron

Job Details: 02/27/2024

"Rollers and idler have worn from use, unit is heating well. Needs repair kit. Approved onsite. Removed and replaced components. Tested unit, working and heating well. Repair kit 4392067 $76.48Tax $6.27Supplies $14.50Hc $129.95Labor $199.95Total job $427.15No return on parts Auth total job $427.15 #34VJLY"

We serviced a

KITCHENAID WALLOVEN

Model KSGG700ESS2

Near Colorado Springs, CO 80924

Aaron

Job Details: 02/27/2024

"LF and LR burner orifices clogged, cleared orifices and electrodes of debris, tested and lighting well now, educated customer of burner difference between single and double orifice burners. Advised customer of 5 star survey."

We serviced a

GE COOKTOP - ELECTR

Model PP9030SJ1SS

Near Colorado Springs, CO 80924

Kris

Job Details: 02/27/2024

installed element ran test op all ok at this time.

We serviced a

WHIRLPOOL RESIDENTIAL REFR

Model WRS588FIHZ04

Near Colorado Springs, CO 80918

Glenn

Job Details: 02/27/2024

"Install New Icemaker & Shelf. Cycle Test IM > Pass, Fill Test> Pass"

We serviced a

MIDEA DISHWASHER

Model MDT24H2AST

Near Colorado Springs, CO 80923

Jessie

Job Details: 02/27/2024

Replaced bad latch. Test op. Leak strip added. All.ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRF555SDFZ18

Near Florissant, CO 80816

David

Job Details: 02/27/2024

Replaced evap motor and control board. Ran diagnostics and operation Running good

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS588FIHZ04

Near Colorado Springs, CO 80920

Glenn

Job Details: 02/27/2024

"Diffuser / Damper part defective again.Techline: Indicates they have seen several reports issues of this type, and Engineering is currently looking into it, however, no resolution as of yet. SR# 7738565575Called Tradecare for Additional Labor Autho# W1AHC30DL1 , Since part is defective, not actually a callback due to tech service provided was accurate."

We serviced a

CAFE RANGE - GAS

Model C2Y366P2TS1

Near Colorado Springs, CO 80904

Ralph

Job Details: 02/27/2024

"made an adjustment to the postion of the valve so it wouldnt drag on the bezel, cust happy with adjustment"

We serviced a

GE DRYER

Model GTD58GBSV0WS

Near Colorado Springs, CO 80906

Roman

Job Details: 02/27/2024

Installed new belt and yes yes s the dryer. Dryer working great and heating up.

We serviced a

WOLF RANGE GAS

Model DF304

Near Colorado Springs, CO 80918

Jessie

Job Details: 02/27/2024

Customer states unit is 50 - 100 degrees off. Using spring style thermo. Oven door not sealing. Very noisey convection fan. Unit reached temp with np issues. Took average on unit. Taking a long time to rebound temps.Temps. unit inner and out bake element no op. Bad relay bdCw fan#809820 $284.34Ccw fan 809818 $245.62Logo#815575 $44.15Hydraulic hinge#812273 $177.70Spring hinge# 812271 $187.56Gasket#816658 $43.03Relay bd#807052 $231.65Total parts $1214.05Tax $99.55Sc $149.95Msrp $14.50Labor 399.95Total $1878.00Customer will think about repair. 2 hours on jon

We serviced a

MAYTAG WASHER

Model MHW5630HW3

Near Divide, CO 80814

David

Job Details: 02/27/2024

"Replaced tub, shocks, springs, and stator Ran diagnostics test, and a quick cycle Appears to be better, washer is on a pedestal Cx will run for a week or 2 to see how it does"

We serviced a

JENNAIR REFRIGERATOR

Model JF42NXFXDE02

Near Colorado Springs, CO 80921

Glenn

Job Details: 02/27/2024

"Verified W/ Scott in office, all covered under warranty, Install New LED Module Kit, All OPS Test:OK. All Lights Now Working."

We serviced a

MIELE FRONT-LOAD WASHE

Model WWH860

Near Manitou Springs, CO 80829

Roman

Job Details: 02/27/2024

Removed hoses off the washer and dryer and removed the stacked kit. Zip tied everything down that needs to be and installed the shipping struts. Made sure tub is secure. SC $149.95Labor $99.95Total cost $249.90

We serviced a

MAYTAG DRYER

Model MED7230HW3

Near Colorado Springs, CO 80906

Carlos

Job Details: 02/27/2024

"Installed control board and U, ran test, runs ok. Cx will observe"

We serviced a

MAYTAG WASHER

Model MHW5630HC2

Near Pueblo, CO 81001

James

Job Details: 02/27/2024

found loose wire at Main board causing ui to not respond. secured wire and tested all ops test good. left litmus

We serviced a

WHIRLPOOL DISHWASHER

Model WDT730PAHZ

Near Colorado Springs, CO 80906

Carlos

Job Details: 02/27/2024

"Ran test, found debris in drain pump, removed, runs all ok"

We serviced a

WHIRLPOOL DRYER

Model WED6620HW1

Near Colorado Springs, CO 80921

Glenn

Job Details: 02/27/2024

Bad Element & T-stats. Install New Element & T-stat kit. All OPS Test:OK

We serviced a

WHIRLPOOL WASHER

Model WTW5057LW0

Near Monument, CO 80132

Glenn

Job Details: 02/27/2024

"Found worn teeth on Motor cam (Splutch Assy) Installed New Splutch Assy. P/N: W10721967 , Had Logan in Office add part to ticket, I will pick up in office for tomorrows job I borrwed it from. If problem returns, order new Shifter - W11481722 , And re-order cam kit. , ALL OPS TEST:OK"

We serviced a

WHIRLPOOL DISHWASHER

Model WDTA50SAKZ1

Near Colorado Springs, CO 80906

Carlos

Job Details: 02/27/2024

"Found water in bottom tray, cleaned out, made sure water supply line was tighten, cx education on loading dishes, installed new seal"

We serviced a

ZEPHYR RANGE HOOD

Model ALU-E63CWX

Near Colorado Springs, CO 80922

Jessie

Job Details: 02/27/2024

Replaced control. Unit works much better all ok

We serviced a

SUBZERO FREEZER

Model IC-30FI-RH

Near Colorado Springs, CO 80904

Ralph

Job Details: 02/27/2024

"unit has a broken wire on the control. will need to be replaced, cust is going to call subzero to get assistance on this part, part 7041813 $266.65, tax 21.87, labor 189.95, other 14.50, total remaining 492.47, cust paying service charge today. cust paid service fee autho no. 4RU4UN"

We serviced a

SAMSUNG DISHWASHER

Model DW80R2031UG/AA

Near Fountain, CO 80817

Mathew

Job Details: 02/27/2024

"Found bad touch control. Replaced main pcb and touch control, tightend wire nut at terminal block. Test op all okay."

We serviced a

SAMSUNG MICROWAVE

Model ME19R7041FS

Near Fountain, CO 80817

Mathew

Job Details: 02/27/2024

"Replaced all high voltage side components and wire harness. Test op all okay but strong smell from charred inner cabinets persist. Called techline to document, agent sent this ticket for review, will contact Cx when decision is made."

We serviced a

SAMSUNG RANGE

Model NE63A6511SG/AA

Near Fountain, CO 80817

Mathew

Job Details: 02/27/2024

Replaced bulb assembly. Test op all okay.

We serviced a

MAYTAG DRYER

Model MGD6200KW0

Near Carbondale, CO 81623

James R

Job Details: 02/27/2024

"Customer signed disclaimer. Unit will ignite and heat for a bit and then quit. Removed control panel. Checked igniter relay checked good. Removed rear panel. Checked wire harness and thermals all ok. Reassembled then removed top,front of unit checked connections at coils ok. checked motor ok. checked igniter connector found it not snapped in properly. Connected right. Reassembled unit test run is operating as should. Please fill out whirlpool tech satisfaction survey. Thank You. Customer paid Service call $99.00 auth code. A9TXY9"

We serviced a

AMANA DRYER

Model NED4655EW1

Near Colorado Springs, CO 80927

Aaron

Job Details: 02/27/2024

"Thermostat shorted out, replaced heating element and thermostat, tested unit, good temperature wavelengths, vent hose crushed and lint in hose, cleared lint and placed unit in proper location to allow best airflow. Recommend rigid vent hose. Advised customer of 5 star survey."

We serviced a

KITCHENAID MICROWAVE OVEN

Model KOCE500EBS22

Near Santa Fe, NM 87505

Jason

Job Details: 02/27/2024

installed support unit checks ok

We serviced a

SAMSUNG DRYER

Model DVE45R6300/A3

Near Colorado Springs, CO 80908

Brandon

Job Details: 02/27/2024

Replaced heater and tested op all checks hass oqc passed

We serviced a

DACOR OVEN

Model HWO130FS

Near Monument, CO 80132

Brandon

Job Details: 02/27/2024

"Replaced hinges and dampers, door is flush now all checks ok"

We serviced a

WHIRLPOOL DISHWASHER

Model WDF520PADM9

Near Rio Rancho, NM 87144

Joe

Job Details: 02/27/2024

cx complaint - dishes are still dirty after - replaced parts ordered last visit - tested unit - unit good to go

We serviced a

SAMSUNG REFRIGERATOR

Model RF23CB9900QKAA

Near Colorado Springs, CO 80921

Brandon

Job Details: 02/27/2024

"Blank screen, checked connections all ok, replaced parts and tested op all checks ok hass oqc passed"

We serviced a

WHIRLPOOL WASHER

Model WTW4855HW3

Near Carbondale, CO 81623

James R

Job Details: 02/27/2024

Signed disclaimer. Customer had issues several times with unit not starting. No apparent error codes. Replaced control. Calibrated unit and did a service diagnostics test operating as should. Please fill out whirlpool tech satisfaction survey. Thank You. Unit leased 12/4/2023

We serviced a

WHIRLPOOL RANGE

Model WFE515S0JS1

Near Aspen, CO 81611

James R

Job Details: 02/27/2024

Customer signed disclaimer. Replaced cooktop operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.

We serviced a

SAMSUNG DRYER

Model DVE50BG8300VA3

Near Colorado Springs, CO 80904

Mathew

Job Details: 02/27/2024

"Found dent in side of machine, barrel rubbing against case. Found bad roller. Replaced all rollers and straightened out case, Cx happy with operation of dryer."

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS04

Near Corrales, NM 87048

Joe

Job Details: 02/27/2024

"cx complaint - no cool, clicking sounds only - inspecte unit - found condenser fan blades coming off - fixd blades - tested unit - unit starting to cool now"

We serviced a

WHIRLPOOL OVEN

Model JMW3430DS03

Near Corrales, NM 87048

Joe

Job Details: 02/27/2024

cx complaint - not turning on - replaced control - tested unit - unit good to go

We serviced a

GE DRYER

Model PTD70EBPTDG

Near New Castle, CO 81647

Erik

Job Details: 02/27/2024

idler pulley binding and squealing - pull drum and reset idler pulleytest with CX: sounds normal - CX will test fully loaded and C/B may be requiredC/B will need: WE03X33642 &WE03X33643CX will call back if needed

We serviced a

GE WASHER-DRYER COM

Model GUD24ESSM1WW

Near Silt, CO 81652

Erik

Job Details: 02/27/2024

EH to return extra motorinstall motor and switch/ test: GOODHEAT: GOODJOB COMPLETE

We serviced a

WHIRLPOOL M/W OTR

Model WMH31017HS10

Near Santa Fe, NM 87507

Jason

Job Details: 02/27/2024

installed motor unit checks ok

We serviced a

BOSCH REFRIGERATOR

Model B36CL80ENS/09

Near Carbondale, CO 81623

Erik

Job Details: 02/27/2024

floor/walls uneven *see quick picsinstall/ builder to address level flooring (back legs do NOT level on unit) and wall out of level on the right hand sideattempt ot level unit with no success - impossible to level rear legs - no parts can reconcile floor levelCX does not want to sign for JOB 517307JOB COMPLETE

We serviced a

BOSCH DISHWASHER

Model SHPM78Z55N/20

Near Aspen, CO 81611

Erik

Job Details: 02/27/2024

install/ test: GOODJOB COMPLETE

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRT318FMDB09

Near Albuquerque, NM 87105

Larry

Job Details: 02/27/2024

Installed door and tested good - Unit is good to go

We serviced a

KITCHENAID COOKTOP

Model KICU569XBL00

Near Santa Fe, NM 87508

Jason

Job Details: 02/27/2024

Installed part found fuse on other IPC blew. part is discontinued spoke with techline to verify SR7738562173 RESOLUTION TEAM WILL CONTACT CX IN 2-3 BUSINESS DAYS FOR A RESOLUTION

We serviced a

KITCHENAID REFRIGERATOR

Model KRSC703HPS01

Near Santa Fe, NM 87508

Jason

Job Details: 02/27/2024

checked unit found there was an item blocking airflow to sensor causing unit to not properly sense temp in ff section removed item also spoke with cx on loading in the future

We serviced a

GLADIATOR REFRIGERATOR

Model GARF30FDGB04

Near Aspen, CO 81611

James R

Job Details: 02/27/2024

Customer signed disclaimer. Replaced pedal had gotten bent. Please fill out whirlpool tech satisfaction survey. Thank You.

We serviced a

WHIRLPOOL WASHER

Model WTW5105HC3

Near Albuquerque, NM 87121

Larry

Job Details: 02/27/2024

Arrived to house and found it gated and derelict with all the windows broken out. I am not comfortable going to this house and will not be returning

We serviced a

WHIRLPOOL WASHER

Model WTW4816FW3

Near Albuquerque, NM 87121

Larry

Job Details: 02/27/2024

Installed gear case and tested good - Unit is good to go

We serviced a

MAYTAG DISHWASHER

Model MDB8959SFH4

Near Albuquerque, NM 87120

Larry

Job Details: 02/27/2024

Installed gasket and tested good - Unit is good to go

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS325SDHZ08

Near Rio Rancho, NM 87144

Larry

Job Details: 02/27/2024

CX Complaint - Fridge making noise - Inspected unit and found ice build-up caused by water dripping behind the evap cover/air duct from the IM fill tube - Called techline (SR7738562489) Found crack in liner behind air duct - Unit is un-repairable

We serviced a

KITCHENAID REFRIGERATOR

Model KFIS29BBMS00

Near Los Lunas, NM 87031

Larry

Job Details: 02/27/2024

Installed parts listed and tested good - Unit is good to go

We serviced a

WHIRLPOOL DISHWASHER

Model WDP540HAMZ2

Near Leadville, CO 80461

Antonio

Job Details: 02/27/2024

Installed new sump motor and kinked drain line straightened out unit tested good also advised cx of water strips

We serviced a

GE WASHER-DRYER COM

Model GUD27ESSM1WW

Near Carbondale, CO 81623

Erik

Job Details: 02/27/2024

vent clogged/ obstruction/ bad HVAC or install - heater works on all cycles and options but shuts down due to poor flow and thermistor reading high. please call installer or HVAC vent cleanerCX not available for signature

We serviced a

MAYTAG DRYER

Model MED7230HC3

Near Albuquerque, NM 87114

Joe

Job Details: 02/27/2024

cx complaint - dryer stopped working mid cycle. - cx stated only happened 1 time - inspected unit - no error codes - could not duplicate issue

We serviced a

WHIRLPOOL DISHWASHER

Model WDT750SAKZ1

Near Monument, CO 80132

Glenn

Job Details: 02/27/2024

"Door to New Home was left open, No one onsite to sign.F1E1 - Control: ACU FailureSRC PWR Good, Wired properly. Reseat connections to PCB, ALL OPS Test:OK, No Error Codes reported."

We serviced a

WHIRLPOOL WASHER

Model WTW8127LC1

Near Fountain, CO 80817

Carlos

Job Details: 02/27/2024

"Called Techline SR#7738559395, made sure center screw was tighter, noise is normal operation of clutch and slider, clutched releases magnetized slider into rotor, rotation of rotor makes slider fall into place, making cluncking noise, unit working as designed."

We serviced a

SAMSUNG REFRIGERATOR

Model RF23HCEDBSR/AA

Near Colorado Springs, CO 80908

Brandon

Job Details: 02/27/2024

"Error 40c, replaced parts and tested op all checks ok"

We serviced a

ZEPHYR RANGE HOOD

Model ALU-E63CWX

Near Colorado Springs, CO 80922

Kris

Job Details: 02/27/2024

helped jessie

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS321SDHZ08

Near Colorado Springs, CO 80919

Glenn

Job Details: 02/27/2024

"Reseat connections to Icemaker, Cycle Test:OK, All OPS Test: OK"

We serviced a

FRIGIDAIRE REFRIGERATOR SID

Model FRSS26L3AF0

Near Pueblo, CO 81007

James

Job Details: 02/27/2024

"installed ordered parts. tested ops all ckok frost pattern starting, noise gone. advised cust 24-36 hours for temp to settle. part sales final"

We serviced a

THERMADOR OTR MICROWAVE

Model MB30WS/02

Near Pueblo West, CO 81007

James

Job Details: 02/27/2024

installed ordered parts. tested ops all ckok

We serviced a

WHIRLPOOL DRYER

Model WGD4815EW4

Near Tijeras, NM 87059

Jason

Job Details: 02/26/2024

checked unit found neutral wire connection was loose at motor tightened connector unit checks ok

We serviced a

SAMSUNG REFRIGERATOR

Model RS261MDBP/XAA

Near Colorado Springs, CO 80915

Ralph

Job Details: 02/26/2024

"unit has some vibration from the coppper tubing coming from the compressor, nothing serious to worry about, did manipulate some of the copper but also has alot of water line coppeer behind unit that is causing vibration as well.cust approved the repair...autho no.xcw94x"

We serviced a

GE REFRIGERATOR/TOP

Model GSE25GYPCFS

Near Colorado Springs, CO 80915

Jessie

Job Details: 02/26/2024

Took apart the back of the unit where customer was hearing noise. Unit is cooling properly and will produce a frequency. Took sound recording of unit and reading less than 40 decimals. Less than a quite library. Went over all operations and made sure all ok

We serviced a

WHIRLPOOL REFRIGERATOR

Model WRS571CIHZ05

Near Pueblo, CO 81001

James

Job Details: 02/26/2024

found ice maker not harvesting water supply good. installed preordered icemaker

We serviced a

SAMSUNG REFRIGERATOR

Model RF28HFEDTSR/AA

Near Colorado Springs, CO 80909

Jessie

Job Details: 02/26/2024

"Got filter out and instructed customer. Unit icemaker needs to be sealed, Icemaker, auger, sealant, clips and bd. Customer wants to reach out to samsung"

We serviced a

SAMSUNG DISHWASHER

Model DW80CG5451SRAA

Near Colorado Springs, CO 80922

Brandon

Job Details: 02/26/2024

"Found loose plastic piece in drain pump, refastened piece and tested op 3 times, error not coming up no all other checks ok hass oqc passed leak strip installed"

We serviced a

SAMSUNG DRYER

Model DVE45T3400P/A3

Near Colorado Springs, CO 80920

Brandon

Job Details: 02/26/2024

Replaced heater assy and tested op all checks ok

We serviced a

PROFILE MICROWAVE

Model PER72279L158

Near Colorado Springs, CO 80904

Ralph

Job Details: 02/26/2024

"reset the power and unit staarted working, custs breakers were not set up correctly, found the one for the microwave and now cust can reset poser"

We serviced a

WHIRLPOOL DRYER

Model WED5100HW

Near Pueblo, CO 81005

Domingo

Job Details: 02/26/2024

Check the dryer outlet no power need electrician couldnt find tripped breaker

We serviced a

WHIRLPOOL WASHER

Model LSR5132PQ0

Near Pueblo, CO 81005

Domingo

Job Details: 02/26/2024

Replace pum and switch and put screws were they were missing test it and it drain

We serviced a

MAYTAG DRYER

Model MEDC465HWO

Near Pueblo, CO 81005

Domingo

Job Details: 02/26/2024

Replace belt roller and pulley idler no more noise

We serviced a

MIELE COFFEE MACHINE

Model CM6360

Near Colorado Springs, CO 80903

Jessie

Job Details: 02/26/2024

F0010 - no water supplyF0042 - mains frequency registration faultF0073 - brew unit drive fault F0074 - control valve m29 drive faultF0076 - brew unit compression fault. Drive assy#11682260 $698.11Control valve m29#11682492 $551.60Total parts $1249.71Tax $102.48Sc $149.95Msrp $14.50Labor $309.95Total $1826.59

We serviced a

WHIRLPOOL DRYER

Model WED5100HW3

Near Colorado Springs, CO 80919

Glenn

Job Details: 02/26/2024

"Spoke w/ Amarie in office, Unit is covered under warranty. Customer unable to locate receipt. Loose blower wheel. Tighten blower wheel & motor. All OPS Test:OK, Customer informed of 5 star survey."

We serviced a

KITCHENAID COMPACTOR

Model KTTS505ESS2

Near Colorado Springs, CO 80919

Glenn

Job Details: 02/26/2024

"Spoke with Amarie in Office, as customers son let me in, and doesn't have access to POP. Broken Release pedal. Install New Pedal."

We serviced a

BOSCH DISHWASHER

Model SHX68T55UC/07

Near Colorado Springs, CO 80923

Kris

Job Details: 02/26/2024

ran test op found suds build up in unit suggest cleaning unit regularly. all ok at this time.

We serviced a

INSINKERATOR GARBAGE DISPOSAL

Model BADGER 5XL

Near Colorado Springs, CO 80920

Kris

Job Details: 02/26/2024

installed disposal ran test op all ok at this time cx will monitor unit.

We serviced a

KITCHENAID DISHWASHER

Model KUDS01DLSS6

Near Colorado Springs, CO 80906

David

Job Details: 02/26/2024

"Clean light giving a seven blink. Heat rise not coming up fast enough. Checked heater and is good, control is energizing the heater. There is a possibility that the thermistor is out of spec. Part number 8269208. Water temperature at faucet is a little cool, 110 - 115, recommend 125 - 140.Service fee good for 30 days."

We serviced a

WHIRLPOOL WALLOVEN

Model WOS51EC0HS20

Near Albuquerque, NM 87114

Joe

Job Details: 02/26/2024

cxcomplaint - oven not always turning on - replaced parts ordered last visit - tested unit - unit good to go

We serviced a

KITCHENAID REFRIGERATOR

Model KRMF706ESS01

Near Colorado Springs, CO 80924

Aaron

Job Details: 02/26/2024

"Removed and replaced components, unit is working well now. Installed litmus strip. Advised customer of 5 star survey."

We serviced a

BOSCH DISHWASHER

Model SHP878ZD5N/18

Near Colorado Springs, CO 80903

Ralph

Job Details: 02/26/2024

unit would be to costly for cust to repair he is going to find a diff unit....autho no. 9F4FFW

We serviced a

KITCHENAID DISHWASHER

Model KDTE704DPA0

Near Colorado Springs, CO 80904

David

Job Details: 02/26/2024

Replaced malfunctioning UIRan diagnostics and a short cycle All running good

We serviced a

KITCHENAID REFRIGERATOR

Model KRFF507HBS00

Near Colorado Springs, CO 80921

Glenn

Job Details: 02/26/2024

Install New Module Kit. All OPS Test:OK

We serviced a

JENN-AIR WALLOVEN

Model JMW2430LL02

Near Colorado Springs, CO 80921

Glenn

Job Details: 02/26/2024

"Install New Bulb, All OPS Test:OK, Folled up w/Techline: Ref SR# 7738138476 , Technical Service Pointer #: W11493384 Rev. C , Unit appears to work as designed, as long as customer always uses center of door handle to open / close door, and give it a good close to engage both door switches (Which are very sensitive.)"

We serviced a

DACOR REFRIGERATOR

Model DYF42SBIWR

Near Colorado Springs, CO 80906

Ralph

Job Details: 02/26/2024

"unit has a bad filter housing, cust going to replace hisself...autho no. Y9E4C9"

We serviced a

SAMSUNG DRYER

Model DV45K7600EW/A3

Near Colorado Springs, CO 80920

Kris

Job Details: 02/26/2024

ran test op found motor shorting out control. will need listed parts before I can make a determination of any other issues. control dc92-01729b 268.15motor dc93-00101u 397.85

We serviced a

THERMADOR REFRIGERATOR

Model T36IB70NSP/26

Near Colorado Springs, CO 80906

Ralph

Job Details: 02/26/2024

"unit not cooling very well in the fz area and not making ice, cleaned condenser which was dirty and told cust to monitor the unit for any compressor damage due to the dirty condenser, autho no. 34HV93"

We serviced a

GE DISHWASHER

Model GDF510PSRSS

Near Pueblo, CO 81001

James

Job Details: 02/26/2024

found tub warping slightly causing door to not latch properly called ge tech line and found tub is non-repairable. cust relations will reach out to cust.

We serviced a

WHIRLPOOL WASHER

Model WTW5105HC3

Near Colorado Springs, CO 80904

Roman

Job Details: 02/26/2024

"Removed the old motor and belt and shield, installed new support rods, motor, belt and capacitor. Calibrated the washer and ran a test cycle washer seems to be working great. Made sure it was level. Ran another cycle and made sure washer was working properly. Showed cx how to use cycles and what to do them with, also recommend deep water wash with loads."

We serviced a

MIELE OVEN

Model H7680BP

Near Colorado Springs, CO 80904

Jessie

Job Details: 02/26/2024

Ran unit up to 400 degrees. Customer using spring style thermo. Stuck my temp lead in the unit next to their thermometer. Connect mdu. No errors found. Went to sensors and confirmed the sensors reading temp in the oven. Customer needs to wait 15 mins after preheat to get desired temp.