We serviced a
MAYTAG WASHER
Model MVWP576KW0
Near Peyton, CO 80831
Aaron
Job Details:
01/23/2024
"Removed and replaced valve assembly and control, calibrated control and tested unit through diagnostics and bulky cycle, working well now. Advised customer of 5 star survey."
We serviced a
SAMSUNG DISHWASHER
Model DW80R7060US/AA
Near Colorado Springs, CO 80921
Jessie
Job Details:
01/23/2024
Sc error. Slow drain. Took apart the pump and found piece of coffee cup in the pump.
We serviced a
WHIRLPOOL RANGE
Model WFG550S0LZ4
Near Peyton, CO 80831
Jerimiah
Job Details:
01/23/2024
"Unit inconsistently igniting, and multiple times tries to reignite during preheat. Found oven connected to GFCI breaker and is also being shared with microwave. Advised to isolate each appliance and set to standard breaker over gfci per installation information. Adjusted bake pipe to proper high altitude setting, adjusted surface burners to proper height. Unit check ok. W11162730 DSI board"
We serviced a
JENN-AIR WALLOVEN
Model JMW3430LL02
Near Colorado Springs, CO 80908
Aaron
Job Details:
01/23/2024
"Removed and replaced both oven fan blades, tested unit at 425f, working well now, verified by customer. Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Colorado Springs, CO 80923
Aaron
Job Details:
01/23/2024
"Motor dispenser has power, but is weak, coupling was able to come off of shaft, removed and replaced dispenser motor, tested and working well now. Advised customer of 5 star survey."
We serviced a
GE REFRIGERATOR
Model GTE17GSNBRSS
Near Fountain, CO 80817
Roman
Job Details:
01/23/2024
"Water line has a leak where it goes into the floor, cx had a lot of line left and wanted to use it and not replace the entire line. Cut the line and wrapped it behind the fridge and under the floor. Labor $100.00Sc $129.95 Total cost $229.95. $229.95 CK Auth# H4WW3J *wants invoice mailed"
We serviced a
SAMSUNG DRYER
Model DVE45T6000W/A3
Near Colorado Springs, CO 80906
Roman
Job Details:
01/23/2024
"Turned the dryer on and it will only click, took the dryer apart and the belt was not around the idler pulley, belt and pulley are okay. Put the dryer back together and tested it, dryer is spinning and heating. Recommend not drying heavy uneven loads. Paid sc $129.95 CC Auth# 4ULAJ4"
We serviced a
SAMSUNG WASHER FRONT LOA
Model WF45K6500AV/A2 11
Near Colorado Springs, CO 80905
Roman
Job Details:
01/23/2024
"Ran the washer in diagnostics and washer ran through it all okay, ran a normal cycle and washer stopped at 11 minutes into the cycle, checked control board and motor. Unplugged the hall sensor and plugged back in, washer ran through a cycle. Recommend replacing the hall sensor. Sensor #DC31-00098A $132.20Tax $10.84Part total $143.04MPs $14.50Labor $249.95Sc $129.95Total cost $537.44Paid sc"
We serviced a
MAYTAG WASHER
Model MVW6200KW1
Near Colorado Springs, CO 80927
Aaron
Job Details:
01/23/2024
"Lid lock assembly is shorted out, control cannot sense, verified power at control, unable to test unit further as lid lock is first step in diagnostics. Discussed situation with techline. SR7738302529 Needs latch. Approved onsite. Removed and replaced latch assembly. Tested unit through diagnostics, working well now. Latch w11700916 $85.02Tax $6.97Supplies $14.50Hc $149.95Labor $179.95Total job $436.39No return on parts Auth total due $436.39 #WN33R4"
We serviced a
BOSCH WALL OVEN
Model HBL8750UC/11
Near Colorado Springs, CO 80918
Jerimiah
Job Details:
01/23/2024
Installed replacement display board. Unit check ok charged labor as quoted $199.95 CC Auth# 94HYN9
We serviced a
DACOR DOWNDRAFT VENT
Model RV36S
Near Colorado Springs, CO 80918
Jerimiah
Job Details:
01/23/2024
"Unit not functioning, no rise no response, parts are available for unit, checked incoming voltage off terminal, unit is a 240 unit, 120 is properly set to blower, 55/55 hot/neu going to control board is not. Cust will have to have electrician repair incoming power. Charging 2nd appl sc $99.95 CC Auth# CN43L982633 button board700991 control76457 motor"
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS20
Near Monument, CO 80132
Glenn
Job Details:
01/23/2024
"Install New Switches Harness Assy, Sensor, Magnetron & Inverter. All OPS Test:OK"
We serviced a
DACOR SINGLE WALL OVEN
Model MCS130S
Near Colorado Springs, CO 80918
Jerimiah
Job Details:
01/23/2024
"Unit not heating, convection motor making noise. Parts are NLA charging service call $164.95 CC Auth# LAUE3LDE81-05672A RELAY BOARD NLADE81-05631A CONV MOTORDE81-06277A BAKE ELEMENT"
We serviced a
WHIRLPOOL DISHWASHER
Model WDT750SAKZ0
Near Fountain, CO 80817
Carlos
Job Details:
01/23/2024
Installed control board ran test op all ok.
We serviced a
BOSCH REFRIGERATOR
Model B36CD50SNS/02
Near Manitou Springs, CO 80829
Ralph
Job Details:
01/23/2024
"unit not draing properly, cleared ice and cleared obstruction in the fz evap drain hole....Amy one hour on this call please"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRT511SZDM02
Near Colorado Springs, CO 80921
Glenn
Job Details:
01/23/2024
"Attempted to replace FF Door switch, however; wires are foamed in deep into cabinet. Unable to install new switch. Techline: Submitted picture to: robert_yon@whirlpool.com , SR# 7738304449 , Techline submitted for replacement, Customer will receive a call from Manuf. within 3 business days."
We serviced a
WHIRLPOOL WASHER
Model WTW5540SQ0
Near Pueblo, CO 81001
James
Job Details:
01/23/2024
installed ordered parts. tested ops all ckok
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, CO 80925
Carlos
Job Details:
01/23/2024
"Called Techline SR 7738302675. Replaced heating element. Dryer has temperatures in cycle up to 159 down to 130 degrees, heats ok. Cx has a foil metal vent, cx has to replace vent and clean vents to improve air flow."
We serviced a
GE RANGE
Model PGS950SEF5SS
Near Colorado Springs, CO 80908
Jerimiah
Job Details:
01/23/2024
"Bake igniter dead, needs replacing. Cust holding off on repairs. Labor will be $189.95 upon return service. Charging service call $136.45 CC Auth# A9MF93WB13K10043 bake igniter $177.02"
We serviced a
WHIRLPOOL WASHER
Model WTW8127LW1
Near Rifle, CO 81650
James R
Job Details:
01/23/2024
Signed disclaimer. Replaced UI and electronic control. Calibrated unit. Test then in service diagnostics. Unit is working as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
SAMSUNG REFRIGERATOR
Model RS22T5201SR/AA
Near Colorado Springs, CO 80923
Mathew
Job Details:
01/23/2024
"Found ice build up in ice route. Replaced ice room assy, auger and bun. Test op all okay."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Colorado Springs, CO 80923
Mathew
Job Details:
01/23/2024
"Replaced all icemaker parts. Sealed room, test op all okay."
We serviced a
MAYTAG WASHER
Model MVWB755DW0
Near Albuquerque, NM 87114
Joe
Job Details:
01/23/2024
"cx complaint - wont finish cycle qnd leaks - inspected unit - gearcase leaking - needs clutch, gearcase, drain pump and possibly control board - customer declined repair"
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Breckenridge, CO 80424
Antonio
Job Details:
01/23/2024
Installed new water valve unit tested good
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
01/23/2024
"Errors 39c, 40c, replaced ice maker, auger clip broke replaced auger assy, tray cracked replaced tray, applied service tips, tested op all checks ok hass not compatible"
We serviced a
SAMSUNG REFRIGERATOR
Model RF28HMEDBSR/AA
Near Colorado Springs, CO 80927
Mathew
Job Details:
01/23/2024
"Replaced all icemaker parts, sealed room test op all okay."
We serviced a
SAMSUNG REFRIGERATOR
Model RF22K9381SR/AA
Near Colorado Springs, CO 80921
Mathew
Job Details:
01/23/2024
"Replaced all icemaker parts, sealed room and test op all okay."
We serviced a
SAMSUNG REFRIGERATOR
Model RF22R7351SG/AA
Near Colorado Springs, CO 80922
Mathew
Job Details:
01/23/2024
"Replaced icemaker, auger and board. Sealed room and test op all okay."
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950UG
Near Colorado Springs, CO 80915
Mathew
Job Details:
01/23/2024
Replaced wash vane and test op. All okay.
We serviced a
MAYTAG DRYER
Model MED6230HW3
Near Colorado Springs, CO 80921
Glenn
Job Details:
01/23/2024
"Reseat connections to PCB. All OPS Test:OK, Vent system appears to be ok, however; suggest have vent system cleaned at least once per year. All Talked about Timed Dry Cycle option."
We serviced a
WHIRLPOOL WASHER
Model WTW5057LW0
Near Colorado Springs, CO 80920
Glenn
Job Details:
01/23/2024
cycle will not run - sp w11632927 - special project s17538Install New Capacitor. All OPS Test:OK
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRB322DMBM05
Near Rifle, CO 81650
James R
Job Details:
01/23/2024
Signed disclaimer. Adjusted the unit tilted back so door will shut more on its own. Explained to customer that the freezer door has a self aligning feature so the drawer will close properly. This is the design of it. If pull more on the left side can hear the gears slip this is normal when door shuts it straightens out. Operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHZ03
Near Pueblo West, CO 81007
Kris
Job Details:
01/23/2024
installed compressor ran test op all ok at this time. cx will monitor unit for 24 hours before loading with food.
We serviced a
BEKO FRENCH DOOR REFR
Model BFFD3624XSS
Near Pueblo, CO 81007
Kris
Job Details:
01/23/2024
helped jk
We serviced a
KITCHENAID DISHWASHER
Model KDTE204KPS1
Near Aspen, CO 81611
James R
Job Details:
01/23/2024
Signed disclaimer. Replaced Console. Test functions of all cycles and options. They are working as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
MAYTAG WASHER
Model MHW5630HW3
Near Woodland Park, CO 80863
David
Job Details:
01/23/2024
Replaced main control board Ran diagnostics quick cycle All good Cycle selecte going where they are supposed to
We serviced a
WHIRLPOOL DRYER
Model WED4815EW1
Near Albuquerque, NM 87114
Joe
Job Details:
01/23/2024
cx complaint - taking too long to dry - inspected unit - found bad heater element - replaced element - unit good to go; used 1 279838 (element) from stock
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHZ04
Near Rio Rancho, NM 87124
Joe
Job Details:
01/23/2024
cx complaint - not making ice and not cooling correctly - inspected unit - makinmg ice fine now and all temperatures were within range - culd not duplicate issues
We serviced a
WHIRLPOOL WASHER
Model WTW4816FW3
Near Blue River, CO 80424
Antonio
Job Details:
01/23/2024
Found units clod water line clogged so was timing out cleared unit tested good
We serviced a
WHIRLPOOL WASHER FRONT LOA
Model WFW95HI
Near Aspen, CO 81611
James R
Job Details:
01/23/2024
Cleaned out bellow drain holes and removed front of unit and cleaned out drain pump screen. Reassembled unit. Test operation. Noisy in spin removed rear panel found drain hose not mounted in one place hitting wall. Installed a zip tie. reassembled and test. Ok Customer paid $209.00 service call auth code EYYH9KPlease fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL WASHER
Model WTW5105HW3
Near Rio Rancho, NM 87124
Joe
Job Details:
01/23/2024
cx complaint - washer isn't dispensing fabric softener - replaced dispenser and drawer - unit good to go
We serviced a
WHIRLPOOL WALLOVEN
Model WOC54EC0AS04
Near Albuquerque, NM 87120
Larry
Job Details:
01/23/2024
CX complaint - MW light not working - Inspected unit and found the lame failed - Replaced lamp with pre-id part and tested good - Unit is good to go
We serviced a
WHIRLPOOL DRYER
Model WHD560CHW2
Near Santa Fe, NM 87505
Jason
Job Details:
01/23/2024
installed drain assy unit opperation checks ok
We serviced a
WHIRLPOOL DISHWASHER
Model WDP540HAMZ4
Near Albuquerque, NM 87120
Larry
Job Details:
01/23/2024
CX complaint - Not draining - Inspected unit and found the drain pump failed - Replaced pump and tested good - Unit is good to go
We serviced a
WHIRLPOOL M/W OTR
Model WML75011HZ10
Near Albuquerque, NM 87114
Larry
Job Details:
01/23/2024
CX complaint - Truntable comes off track - Inspected unit and noticed the cx is shorter than usuall and may be bumping the turntable when putting items in the MW - I also noticed a couple very hard grains of rice that may have contributed to the turntable to come off track - I ran the unit a few times for two minuts at a time with no issues - Advised cx to take better care when placing items in MW - Called teckline to document (SR7738308454) - Unit is operating as designed
We serviced a
KITCHENAID DISHWASHER
Model KDTE254ESS2
Near Rio Rancho, NM 87124
Larry
Job Details:
01/23/2024
CX complaint - DW leaking - Inspected unit and found an extra piece of insulation inside the door that was hanging into the lip of the tub and wicking up and out and dripping on the floor - Removed extra insulation and tested good - Unit is good to go
We serviced a
MAYTAG DISHWASHER
Model MDB9959SKZ1
Near Albuquerque, NM 87107
Larry
Job Details:
01/23/2024
CX complaint - Not draining - Inspected unit and found the drain pump failed - Replaced with pre-id parts and tested good - unit is good to go
We serviced a
WHIRLPOOL DRYER
Model WED4950HW0
Near Santa Fe, NM 87507
Jason
Job Details:
01/23/2024
checked unit found loose connection at timer re seated plug unit checks ok
We serviced a
WHIRLPOOL WASHER-DRYER COM
Model WETLV27HW3
Near Santa Fe, NM 87507
Jason
Job Details:
01/23/2024
checked unit found a piece of sheet metal vibrating corrected fitment unit checks ok
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS321SDHZ11
Near Santa Fe, NM 87507
Jason
Job Details:
01/23/2024
checked unit found roller adjustment bolt want screwed in. installed screw and adjusted level unit checks ok
We serviced a
GE REFRIGERATOR
Model GSS25LSLLCSS
Near Woodland Park, CO 80863
David
Job Details:
01/23/2024
Replaced freezer ledWorking good
We serviced a
JENN-AIR WALLOVEN
Model JMW2430IM03
Near Dillon, CO 80435
Antonio
Job Details:
01/23/2024
Installed new ui panel unit tested good Sc$149.95Lb189.95$339.90 CK Auth# 4U4W39
We serviced a
SAMSUNG MICROWAVE
Model ME21R7051SG/AA
Near Colorado Springs, CO 80922
Brandon
Job Details:
01/23/2024
"Buzzing noise when unit runs, called tech support documented via vs, need to replace high voltage components and wire harness, tech support said to close this ticket and create a new ticket to order parts on"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRX735SDHZ01
Near Colorado Springs, CO 80911
Carlos
Job Details:
01/23/2024
"Installed module, LEDs ok. Cx will observe"
We serviced a
FRIGIDAIRE RANGE
Model FFEH3051VSA
Near Colorado Springs, CO 80904
Roman
Job Details:
01/23/2024
"Called tech support because I I wanted to find out how this stove top works and if the burners are supposed to pulsate, which indicates the elements are working properly. Burners are supposed to pulsate. Tenent had used 2 pans on low and the right side heated up faster on low but also is a different type of burner. Tech line said they are working they way they are supposed too, explained to tenant how they work and what tech line said."
We serviced a
GE REFRIGERATOR
Model CVE28DP2NBS1
Near Eagle, CO 81631
Erik
Job Details:
01/23/2024
labor $99Install IM asmCX request a bill from office for labor ONLY as all other costs have been satisfied
We serviced a
GE REFRIGERATOR
Model GTS22KYNCRFS
Near Gypsum, CO 81637
Erik
Job Details:
01/23/2024
adjust lower door hinge and door post * see quick picsadd petroleum jelly to door sealJPOB COMOPLETE
We serviced a
JENNAIR MICROWAVE
Model JMW2430IL03
Near Colorado Springs, CO 80908
Jerimiah
Job Details:
01/23/2024
"Rick positions 1-5 are one full bubble off being level, position 6 and bottom of oven liner is level. Explained to Techline as well as sending photos, this unit is under review with engineering. Unit it working properly but food is being sloshed back into back end of dishes. Will contact office when if theres a resolution. Closing call. SR#7738301338"
We serviced a
BEKO FRENCH DOOR REFR
Model BFFD3624XSS
Near Pueblo, CO 81007
James
Job Details:
01/23/2024
found unit with shims in rear of unit installed by builder to level doors but when they did it tweaked chassis causing mullion to be raised higher than designed which snapped off the peg piece at the top. also found dents in top of door presumably from pushing unit in. unit will need both fridge doors and mullion. cannot replace mullion without addressing door and shim issue because it will just break again. cust stated that per builder they are trying to replace unit. advised cust that if that doesn't happen to call back. so we can get parts on order to address concerns. do not want to order parts if unit is getting replaced.
We serviced a
BEKO DISHWASHER
Model 6516541
Near Pueblo, CO 81007
Kris
Job Details:
01/23/2024
helped jk
We serviced a
MAYTAG RANGE
Model MER6600FZ2
Near Colorado Springs, CO 80919
Glenn
Job Details:
01/22/2024
"All OPS Test:OK , Unit has hidden Bake Element which is accessed via RS of Unit. Ohms good, Good Power to Bake Element. Broil also working. Techline: Called as it appeared Bake Element was missing, since cavity had place for where it should be.. SR# 7738297718 , Paid SC fee of $129.95 , Autho# VMA49U"
We serviced a
KITCHENAID REFRIGERATOR
Model KRMF706ESS01
Near Colorado Springs, CO 80906
Ralph
Job Details:
01/22/2024
"cust concerned about the noise coming from the fridge, i explained that this unit has four fans and a compressor and yes there may be one on at all times and not to worry, dont know how the other pars were orderedsince i installed them on previous visit, may be my screw up"
We serviced a
SAMSUNG WASHER
Model WF45R6300AW/US
Near Colorado Springs, CO 80924
Kris
Job Details:
01/22/2024
cx deciding on repairsran test op fond latch not engaging will need listed parts before I can make a determiation if any other issues.door latch dc34-00028a 207.94
We serviced a
JENNAIR REFRIGERATOR
Model JFX2897DRM
Near Colorado Springs, CO 80924
Kris
Job Details:
01/22/2024
installed all parts sent ran test op all ok at this time.
We serviced a
WHIRLPOOL DRYER
Model WED5605MW0
Near Fountain, CO 80817
Carlos
Job Details:
01/22/2024
"Installed control board, and UI, ran test, all ok, cx will observe"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF767SDHV00
Near Grand Junction, CO 81503
James R
Job Details:
01/22/2024
Replaced icemaker sealed cover with silver tape to be sure had no leaks. Reinstalled icemaker housing assy. Replaced electronic control. Started unit and put in diagnostics. Test 56 no errors 57 and 59 checked good cycled good. test 45 icemaker filled operating as should. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF757SDHZ00
Near Peyton, CO 80831
Aaron
Job Details:
01/22/2024
"Removed and replaced ice box fan, ice maker, and module kit, tested through harvest and fill cycles, working well now. Advised customer of 5 star survey."
We serviced a
MAYTAG DISHWASHER
Model MDB4949SKZ1
Near Grand Junction, CO 81504
James R
Job Details:
01/22/2024
Signed disclaimer. Not circulating water replaced sump motor assy. Finish asy. Test in service diagnostics operation normal and no error codes when done. Please fill out whirlpool tech satisfaction survey. Thank You.
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Colorado Springs, CO 80923
Aaron
Job Details:
01/22/2024
"Unit's temperatures upon arrival 16f and 56f, upon inspection found the control is not sending power to defrost assembly, element resistance is low, thermistor has open reading. Needs element, thermistor, and control. Control w11558182 $274.02Element w11650662 $139.76Thermistor wpw10384183 $99.56Total parts $513.34Tax $42.09Supplies $14.50Hc $149.95Labor $249.95Total job $969.8330 day estimate No return on parts Auth 149.95 ck #5123 #K4UM93"
We serviced a
WHIRLPOOL M/W OTR
Model WMH31017HW09
Near Colorado Springs, CO 80925
Carlos
Job Details:
01/22/2024
"Ran test op unable to determine noise, fan, magnetron and turn table motor run ok (cx will observe, and make a recording if it happens again ). Cx education cx was getting door message because Cx was setting timer without opening door first."
We serviced a
GE RANGE
Model JTD5000EN3ES
Near Silt, CO 81652
Erik
Job Details:
01/22/2024
install/test: GOODJOB COMPLETE
We serviced a
MARVEL ICE MACHINE
Model MP15CPP3RP
Near Colorado Springs, CO 80921
Jessie
Job Details:
01/22/2024
Replaced broken grid.unit passed self test. Customer to.monitor ice prpduction.
We serviced a
SAMSUNG WASHER
Model WF220ANWXAA 01
Near Colorado Springs, CO 80926
Roman
Job Details:
01/22/2024
"Ran the washer and it seemed to drain and spin, checked the filter and it was cleaned out. Ran diagnostics and washer seemed to run through it okay. Drain pine was far down the drain tube, raised it and ran washer again, washer draining out faster but still sounds like it backing up in the pipe. Recommend getting it cleaned out. Cx mentioned it happens every once and a while and that indicates a control board issue, took the board out and did notice a couple of areas that are starting to turn black, Part has been discontinued. Paid check #3246 $129.95 CK Auth# NL33H3"
We serviced a
AMANA WASHER
Model NTW4516FW4
Near Colorado Springs, CO 80923
Aaron
Job Details:
01/22/2024
"F7E6 motor error code upon arrival, tested unit through diagnostics, found 2 small holes in drainline, removed and replaced drain hose, draining well now. Advised customer of 5 star survey."
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
01/22/2024
"Replaced inner door and tested op all checks ok, checked for leaks all ok, dispenser opened with hass oqc passed"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHV08
Near Colorado Springs, CO 80915
Carlos
Job Details:
01/22/2024
Installed water valve ran test all ok
We serviced a
BOSCH RANGE
Model HDIP056U/06
Near Pueblo West, CO 81007
James
Job Details:
01/22/2024
found loose wire at ui panel causing panel to be unresponsive secured wire and tested. advised cust on proper use of unit.
We serviced a
SAMSUNG DISHWASHER
Model DW80CG4021SRAA
Near Pueblo, CO 81008
James
Job Details:
01/22/2024
found loose wire at ui causing intermittent touch loss. secured and tested ops ckok. advised cust on proper ops
We serviced a
BOSCH DISHWASHER
Model SHP78CM5N/22
Near Colorado Springs, CO 80921
Jessie
Job Details:
01/22/2024
Leak coming from left hand corner front of dw. Unit is not hitting flood sensor. Noticed unit is not secured to cabinets and the door was hitting when I got here. Took apart door and found insulation fallen in door. Secured door components. All ok
We serviced a
BOSCH REFRIGERATOR
Model B36FD50SNS/01
Near Colorado Springs, CO 80921
Jessie
Job Details:
01/22/2024
Replaced icemaker components. Ran test. Cudtomer to monitor. All okk i
We serviced a
KITCHENAID WALLOVEN
Model KOCE500ESS11
Near Colorado Springs, CO 80908
Aaron
Job Details:
01/22/2024
"F1E5 inverter error upon arrival, waveguide cover and cavity burnt, unspected waveguide and damaged waveguide, discussed with techline, deemed non repairable. SR7738291445Advised customer of 5 star survey."
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS588FIHW00
Near Elbert, CO 80106
Aaron
Job Details:
01/22/2024
"Unit's settings upon arrival 0f and 38f, as was set last time, tested product temperatures for both cavities, 1.4f for FC and 35.6-38.3f for RC, doors are sealing well, product is well placed on the shelves, discussed situation with techline once more, unit working as designed and no further recommendations. SR7738290070. Advised customer of 5 star survey."
We serviced a
SAMSUNG REFRIGERATOR
Model RF28K9070SG/AA
Near Colorado Springs, CO 80908
Brandon
Job Details:
01/22/2024
"Replaced ice maker, tray, PCB and auger assy, all checks ok hass oqc passed, seal"
We serviced a
SAMSUNG GAS RANGE
Model NX60A6511SS/AA
Near Colorado Springs, CO 80924
Mathew
Job Details:
01/22/2024
Replaced faulty spark module. Test op all okay.
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950UG/AA
Near Colorado Springs, CO 80924
Mathew
Job Details:
01/22/2024
Found defective switch in assy motor holder. Replaced switch and control. Test op all okay. If issue persists unit will need sub wire harness (T) dd39-00013t and cover dd63-00151a
We serviced a
SAMSUNG DISHWASHER
Model DW80R9950US/AA
Near Peyton, CO 80831
Brandon
Job Details:
01/22/2024
Replaced water valve and tested op checked for leaks all checks ok hass oqc passed
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FS/AA
Near Colorado Springs, CO 80924
Mathew
Job Details:
01/22/2024
"Found buzzing noise coming from main control. Replaced main control and test op, unit working as expected."
We serviced a
SAMSUNG DRYER
Model DVE53BB8700VA3
Near Colorado Springs, CO 80921
Mathew
Job Details:
01/22/2024
Replaced missing screw. Test op all okay.
We serviced a
SAMSUNG MICROWAVE
Model ME19R7041FS/AA
Near Colorado Springs, CO 80918
Mathew
Job Details:
01/22/2024
Found fault on high voltage side. Replaced capacitor and magnatron. Test op all okay
We serviced a
WHIRLPOOL WASHER
Model WTW7500GC2
Near Rio Rancho, NM 87144
Joe
Job Details:
01/22/2024
cx complant - the lid does not close/open properly and the washer can not lock and unlock - ins
We serviced a
SAMSUNG RESIDENTIAL REFR
Model RF30BB6200QLAA
Near Peyton, CO 80831
Brandon
Job Details:
01/22/2024
Replaced French assy and tested op all checks ok
We serviced a
THERMADOR REFRIGERATOR
Model T36IT71NNP/31
Near Colorado Springs, CO 80908
Jessie
Job Details:
01/22/2024
Replaced freezer inverter. Test op. Compressor took off and starting to cool. Customer to monitor for next 24 hours.
We serviced a
SAMSUNG WASHER
Model WA50R5200AW/US
Near Colorado Springs, CO 80928
Kris
Job Details:
01/22/2024
installed shifter ran test op all ok at this time.
We serviced a
WHIRLPOOL M/W OTR
Model WMH53521HZ06
Near Albuquerque, NM 87106
Larry
Job Details:
01/22/2024
CX complaint - Fan not working properly - Inspected unit and found a a loose harness at the control board to the fan - Secured connection and tested good - Unit is good to go
We serviced a
MAYTAG WASHER
Model MVW7230HW1
Near Tajique, NM 87016
Jason
Job Details:
01/22/2024
installed suspension rods unit checks ok
We serviced a
WHIRLPOOL WASHER
Model WFW87HEDW0
Near Albuquerque, NM 87106
Larry
Job Details:
01/22/2024
"CX complaint - Washer not starting error codes - Inspected unit and found F3E1, F1E2, F5E2, and F6E2 - Unit will need controls - CX does not want to bear the cost of repair and will replace - Collected SC on Tkt#-515843Control - $298.67Sensor - $64.50UI - $501.92 Parts - $865.90Labor - $219.95MSP - $17.50 Sub Total - $1,243.30 Tax - $105.68 Total - 1,348.98"
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRS325SDHZ08
Near Albuquerque, NM 87110
Larry
Job Details:
01/22/2024
Installed switch and tested good - Unit is good to go
We serviced a
WHIRLPOOL REFRIGERATOR
Model WRF535SWHZ10
Near Albuquerque, NM 87111
Jason
Job Details:
01/22/2024
installed parts unit checks ok
We serviced a
GE RANGE
Model PHS93XYP6FS
Near Aspen, CO 81611
Erik
Job Details:
01/22/2024
install/test: GOODJOB COMPLETE
We serviced a
THERMADOR REFRIGERATOR
Model T36FT820NS/02
Near Aspen, CO 81611
Erik
Job Details:
01/22/2024
install parts/test: GOODcan take up to 24 hours to regulate tempsJOB COMPLETE